光梯度力驱动的纳米硅基光开关

通过一道光改变另一道光的传输路线是光子集成网络中重要而长远的目标, 然而, 由于硅材料的光学非线性较弱, 在硅材料上实现开关的全光控制难以实现. 因此本文提出了一种由光梯度力驱动的纳米硅基光开关, 实现了硅基光开关的全光控制. 该光开关由一个部分悬空的微环谐振器和一个交叉波导结构构成, 当通入一道控制光时, 悬空的微环谐振器在光梯度力的作用下发生弯曲, 微环谐振器的谐振波长随之发生变化, 从而实现光信号的传输路线发生改变. 该光开关利用纳米光子制造技术在标准绝缘体上硅晶圆上制造, 实验数据得出其最小消光比为10.67 dB, 最大串扰为 -11.01 dB, 开关时间分别为180 ns和170 ns. 该光开关具有尺寸小, 响应速度快, 低损耗和可拓展等优点, 在片上集成光路、高速信号处理以及下一代光纤通信网络中具有潜在应用.     

Enhanced photoelectrochemical performance of ZnO photoanode with scattering hollow cavities

Abstract ZnO nanoparticles with average diameter of 12 nm were used to fabricate ZnO photoanodes by electrohydrodynamic (EHD) technique for dye-sensitized solar cells (DSSCs). To enhance the light scattering and conversion efficiency, the ZnO film with scattering hollow cavities (HCs) was realized by calcining polystyrene spheres (PSs) in the film. The films had strong light scattering ability and the overall light to electricity conversion efficiency (η) was improved and reached 5.5% under illumination of simulated solar light (AM-1.5, 100 mW/cm²).     

自聚焦材料弧形全光开关的研究

应用光束传播法,比较基于自聚焦和自散焦材料的全光波导开关的开关特性,指出基于自聚焦材料的全光开关具有较低开关功率、数值化多次开关特性等优越性,并对波导参数进行了全面的优化设计。     

与偏振无关的双向3×3光开关结构设计

利用传统成熟的偏振控制技术,设计了一种由偏振光分束器、相位型空间光调制器、反射镜和四分之一波片构成的3×3光开关。该光开关具有结构紧凑规整、功能的实现与信号光的偏振态无关以及可以完成双向交换等特点。根据其路由控制表对该3×3光开关交换模块功能的实现进行了分析,结果表明,通过对各相位型空间光调制器状态的调整,控制通过其信号光的偏振态,完成信号光的路由,该交换模块可以完成输入信号光的全排列无阻塞输出与交换。同时,该交换模块具有一定的扩容和重构能力,对于构建大规模的交换矩阵具有一定的作用。     

光束传播法分析硅交叉波导光开关的光学效应

运用光束传播法对硅交叉波导全内反射光开关中的光学效应进行了详细分析。结果表明：１）光学表面衰减波和泄漏波所引发的光遂道效应对开关特性有重要影响；２）反射端功率的相对大小于与反射区界面位置密切相关，其起因是古斯－汉欣位移；３）合理考虑这些因素的影响可以大大降低器件对折射率变化的要求。     

激光对含偏心核球形粒子的辐射俘获力

利用偏心球形粒子对任意角度入射有形波束散射的理论,从广义米理论出发,根据电磁场的动量守恒及麦克斯韦张量,推导了任意入射波束对偏心球形粒子辐射俘获力的级数表达式,并以高斯波束为例,就离轴入射有吸收偏心球形粒子时的辐射俘获力进行了数值模拟,讨论了束腰半径、吸收系数、内核的相对大小及位置对俘获情况的影响. 关键词： 广义米理论 偏心球 辐射俘获力 光镊     

时域有限差分法数值仿真单光镊中微球受到的光阱力

本文采用三维时域有限差分法(FDTD)和Maxwell应力张量法建立了单光镊在焦点附近俘获球形微粒的光阱力模型,采用基于球矢量波函数(VSWF)的五阶高斯光源作为仿真光源,得到了准确的光场传播.讨论了光源的波长、束腰、偏振态和微球的半径、折射率对光阱力的影响,分析了在单光镊俘获微球时,邻近微球对光阱力的影响.特别研究了光源的偏振态对微球所受光阱力的作用效果,仿真结果表明圆偏振光比线偏振光对微球的俘获力更大;被光镊稳定俘获的微球,会受到邻近微球干扰,失去平衡状态,改变光源的偏振态可以改变微球的受力状态. 关键词： 光镊 光阱力 介质微球 时域有限差分法(FDTD)     

激光尘埃粒子计数器微型光学传感器的研究

研制成功便携式激光尘埃粒子计数器的核心部件———微型光学传感器。该传感器采用直角散射光收集形式,以高功率半导体激光器作为光源,同时采用高性能的PIN型光电二极管作为光电探测器。散射光收集系统为单一大数值孔径的球面反射镜,其对粒子散射光的收集角范围从20°到160°。粒子散射光信号是脉冲信号,其频谱成份主要在高频段,所以在PIN型光电二极管后用一个带通式前置放大器来消除外界的低频噪声,根据米氏散射理论计算了该光学传感器的光散射响应特性,并用聚苯乙烯标准粒子实测了该光学传感器的性能。结果表明,该系统具有高的信噪比、计数效率和尺寸分辨本领。     

Raman scattering enhancement by dielectric spheres

Raman scattering experiments were performed on Si(60 nm)/metal/substrate structures with and without silica microspheres (with a diameter between 0.5 and 5 µm) on top. Raman scattering from the thin Si layer exhibits enhancements (~20) due to the dielectric spheres, where the enhancement factors depend on the diameter of the spheres. The interaction between light and dielectric spheres has been simulated by finite difference time domain calculations (FDTD), wherein particularly the electric energy density (ED) distribution in the thin Si layer was of concern. For microspheres with a diameter less than ~3 µm, the transverse ED distribution (perpendicular to the incident light direction) within the Si layer is characterised by a single peak centered on the optical axis. For larger diameters, a multimodal transverse ED distribution develops where the maximum is not centered on the optical axis. Using an ad‐hoc approach for surface enhanced Raman scattering in combination with the FDTD calculations, the experimental Raman observations are well accounted for. Copyright © 2013 John Wiley & Sons, Ltd.     

4×4自由空间光开关结构及其矩阵分析

光开关是全光通信网络中的一种重要的光无源器件。提出了一种4×4自由空间光开关的结构设计方法,并进行了矩阵理论分析。该4×4光开关具有新颖的光模块化结构,该光开关结构仅由偏振分束组合棱镜,λ／4波片,λ／2波片,直角棱镜,全反镜和偏振光调制器组成,对光开关的控制与输入光束的偏振态无关。所有的输出端口可以和输入端口无阻塞地互连交换。这种新型的光开关结构具有光学元件少,结构紧凑,模块化,与偏振无关的特点。基于4×4光开关的矩阵分析得到了路由控制表,为4×4光开关从任意输人端口到任意输出端口的路由控制状态提供了理论分析手段,从而可以方便地实现无阻塞地光交换开关矩阵的路由控制功能。     

Chiral lateral optical force near plasmonic ring induced by Laguerre-Gaussian beam

Owing to the good adjustability and the strong near-field enhancement, surface plasmons are widely used in optical force trap, thus the optical force trap can achieve excellent performance. Here, we use the Laguerre-Gaussian beam and a plasmonic gold ring to separate enantiomers by the chiral optical force. Along with the radial optical force that traps the particles, there is also a chirality-sign-sensitive lateral force arising from the optical spin angular momentum, which is caused by the interaction between optical orbit angular momentum and gold ring structure. By selecting a specific incident wavelength, the strong angular scattering and non-chiral related azimuthal optical force can be suppressed. Thus the chiral related azimuthal optical force can induce an opposite orbital rotation of the trapped particles with chirality of different sign near the gold ring. This work proposes an effective approach for catchingand separating chiral enantiomers.     

Compton散射下多信道平面光波导的空间光孤子开关

应用量子微扰理论和多光子非线性Compton散射模型,对Compton散射下多信道平面光波导的空间光孤子开关进行了研究.结果表明:在横向具有正弦形周期折射率调制的非线性平面光波导的多信道系统中,原先束缚在一个信道中的孤子可以靠由入射和散射光形成的耦合控制光点,通过交叉相位调制横向吸引孤子波束,使孤子从原信道切换到邻近信道,从而实现光孤子开关的功能.控制光点可由耦合光在势谷之间的横向聚焦来实现.散射既能使控制光点的有效强度的阈值和孤子的辐射损耗增大,势垒增高,幅度下降较小,有利于孤子开关的形成;又能使波束展宽较宽,并存在开关被破坏的危险.由此可见,Compton散射下恰当控制入射激光强度是实现孤子开关的关键.     

Measurements of diffuse backscattering Mueller matrices of turbid media

We report on the development of a method that records spatially dependent intensity patterns of polarized light that arise from illuminating a turbid media with a polarized laser beam and being diffusely backscattered. Our technique employs polarized light from a He-Ne laser () which is focused onto the surface of the scattering medium. A surface area of approximately 2×2 cm centered on the light input point is imaged through polarization analysis optics onto a CCD camera. The Mueller matrix is reconstructed by 49 intensity measurements with various orientations of polarizer and analyzer. The measured Mueller matrix of polystyrene spheres was compared with the theory result of incoherent scattering of light by spheres. The experimental and theory results are in excellent agreement. It appears that the azimuthal patterns of the Mueller matrix are determined by the symmetry of the turbid media.     

采用超连续谱激光的双光束光纤光阱实验

以超连续谱激光器作为捕获光源,首次提出并搭建了超连续谱双光束光纤光阱实验系统,实现了聚苯乙烯微球的捕获和操控。通过改变光纤端面间隔和调整捕获光功率的方式精确控制微球的位置,采用CCD图像分析方法实现了微球位置的精确测量。对微球受限布朗运动下的位置变化进行傅里叶变换,计算得到功率谱,与理论功率谱函数拟合后求出了其光阱刚度。结果表明,捕获光束的功率为28 mW时,光阱刚度达到1.3×10-6N/m,高于相同实验条件下单波长光纤光阱的刚度。与传统采用单色光作为捕获光源的光镊系统不同,超连续谱双光束光阱系统利用其宽谱优势,通过研究被捕获微粒的散射光谱信息可获取其尺寸、折射率等物理特征参数。     

Three-dimensional dynamic optical manipulation by combining a diffractive optical element and a spatial light modulator

Since the introduction of computer-controlled spatial light modulators (SLMs), holographic optical tweezers have become an important tool for dynamic parallel optical manipulation. In this paper we clarify the usefulness of a new configuration for optical trapping that creates light patterns using the combination of a diffractive optical element (DOE) and an SLM. This configuration not only enables the use of the higher part of the SLM’s diffraction efficiency curve, because a simple hologram can be chosen for the SLM, but also achieves three-dimensional dynamic optical manipulation over a large spatial range. By switching blaze-like holograms displayed on the SLM, we demonstrated simultaneous transportation of three 6-μm-diameter polystyrene beads over a range of 90 μm in the vertical direction and 37.5 μm in the horizontal direction. Compared with the same manipulation executed using only the SLM, the range of this method is extended four-fold in the vertical direction and three-fold in the horizontal direction.     

Design of Two-Dimensional Optimized Banyan Networks

A smart two-dimensional optical Banyan network is proposed. Polarization switching logic of light is applied for the design of this network. The main element for the connections of the network is an optical crossbar switch that is composed of a half-wave plate, a programmable polarization switch, and a couple of birefringent plates. By the proposed optical crossbar switches, all permutations of the link patterns required in the network are generated due to the optimized design of the switching logic. As a result, complicated routing control of ordinary Banyan networks is much reduced and a simple two-dimensional optical Banyan network with straight interconnections between successive stages of the networks can be realized.     

All optical switching in semiconductor microresonators based on pattern selection

We present here a method for selecting optical patterns in a passive semiconductor microresonator, by using a spatial perturbation. A pattern is spontaneously generated in the system, and a switching beam causes this pattern to rotate even if the power in the switching beam is much lower than the power in the pattern. Thus, an all optical switch is realized, that operates at low light levels.     

Transverse optical patterns for ultra‐low‐light‐level all‐optical switching

We review recent theoretical and experimental efforts toward developing an all‐optical switch based on transverse optical patterns. Transverse optical patterns are formed when counterpropagating laser beams interact with a nonlinear medium. A perturbation, in the form of a weak switch beam injected into the nonlinear medium, controls the orientation of the generated patterns. Each state of the pattern orientation is associated with a state of the switch. That is, information is stored in the orientation state. A realization of this switch using a warm rubidium vapor shows that it can be actuated by as few as 600 ± 40 photons with a response time of 5 µs. Models of nonlinear optical interactions in semiconductor quantum wells and microresonators suggest these systems are also suitable for use as fast all‐optical switches using this same conceptual design, albeit at higher switching powers.     

Photoinduced Birefringence and Broadband All-Optical Photonic Switch in a Bacteriorhodopsin/Polymer Composite Film

Photoinduced birefringence with large optical nonlinearity in a bacteriorhodopsin/polymer composite film is observed. A high refractive index change of 8.5×10^-5 photoinduced by 476nm pumping beam is reached at the low intensity of 6.5mW/cm². Based on it, a broadband all-optical photonicswitch is realized with an optical controlling switch system. Because of controlling beam's selectivity in switching, the transporting beams of different wavelengths with different intensities and shapes can be modulated by adjusting the wavelength and intensity of the controlling beam.     

All-optical switching in an antiwaveguiding structure

We consider a multichannel optical switch based on a combination of a nonlinear antiwaveguide and several parallel waveguides. The switching is controlled by a perpendicular laser beam focused on the surface of the device. We perform numerical simulations and consider in detail the 1 N switching in such a structure.