Millimeter-wave voltage-controlled oscillators in 0.13-/spl mu/m CMOS technology

This paper describes the design of CMOS millimeter-wave voltage controlled oscillators. Varactor, transistor, and inductor designs are optimized to reduce the parasitic capacitances. An investigation of tradeoff between quality factor and tuning range for MOS varactors at 24 GHz has shown that the polysilicon gate lengths between 0.18 and 0.24 /spl mu/m result both good quality factor (>12) and C/sub max//C/sub min/ ratio (/spl sim/3) in the 0.13-/spl mu/m CMOS process used for the study. The components were utilized to realize a VCO operating around 60 GHz with a tuning range of 5.8 GHz. A 99-GHz VCO with a tuning range of 2.5 GHz, phase noise of -102.7 dBc/Hz at 10-MHz offset and power consumption of 7-15mW from a 1.5-V supply and a 105-GHz VCO are also demonstrated. This is the CMOS circuit with the highest fundamental operating frequency. The lumped element approach can be used even for VCOs operating near 100-GHz and it results a smaller circuit area.     

A 1-V 3.8 - 5.7-GHz wide-band VCO with differentially tuned accumulation MOS varactors for common-mode noise rejection in CMOS SOI technology

In this paper, a 1-V 3.8 - 5.7-GHz wide-band voltage-controlled oscillator (VCO) in a 0.13-/spl mu/m silicon-on-insulator (SOI) CMOS process is presented. This VCO features differentially tuned accumulation MOS varactors that: 1) provide 40% frequency tuning when biased between 0 - 1 V and 2) diminish the adverse effect of high varactor sensitivity through rejection of common-mode noise. This paper shows that, for differential LC VCOs, all low-frequency noise such as flicker noise can be considered to be common-mode noise, and differentially tuned varactors can be used to suppress common-mode noise from being upconverted to the carrier frequency. The noise rejection mechanism is explained, and the technological advantages of SOI over bulk CMOS in this regard is discussed. At 1-MHz offset, the measured phase noise is -121.67 dBc/Hz at 3.8 GHz, and -111.67 dBc/Hz at 5.7 GHz. The power dissipation is between 2.3 - 2.7-mW, depending on the center frequency, and the buffered output power is -9 dBm. Due to the noise rejection, the VCO is able to operate at very low voltage and low power. At a supply voltage of 0.75 V, the VCO only dissipates 0.8 mW at 5.5 GHz.     

A 5-GHz low phase noise differential colpitts CMOS VCO

A low noise 5-GHz differential Colpitts CMOS voltage-controlled oscillator (VCO) is proposed in this letter. The Colpitts VCO core adopts only PMOS in a 0.18-/spl mu/m CMOS technology to achieve a better phase noise performance since PMOS has lower 1/f noise than NMOS. The VCO operates from 4.61 to 5 GHz with 8.3% tuning range. The measured phase noise at 1-MHz offset is -120.42 dBc/Hz at 5 GHz and -120.99 dBc/Hz at 4.61 GHz. The power consumption of the VCO core is only 3 mW. To the authors' knowledge, this differential Colpitts CMOS VCO achieves the best figure of merit (FOM) of 189.6 dB at 5-GHz band.     

On-chip test circuit for measuring substrate and line-to-line coupling noise

An on-chip test circuit has been developed to directly measure substrate and line-to-line coupling noise. This test circuit has been manufactured in a 0.35 /spl mu/m double-well double polysilicon CMOS process and consists of noise generators and switched-capacitor signal processing circuitry. On-chip analog-to-digital conversion and calibration are used to eliminate off-chip noise and to extend the measurement accuracy by removing system noise. A scan circuit is described that enables the noise waveform to be reconstructed. On-chip generators ranging in area from 0.25 /spl mu/m/sup 2/ to 1.5 /spl mu/m/sup 2/ produce noise at the receiver decreasing from 3.14 mV//spl mu/m to 0.73 mV//spl mu/m. Open and closed guard rings reduce the noise by 20% and 85%, respectively. Measurement of test circuits manufactured with an epitaxial process-5.5-/spl mu/m-thick epitaxy with 20 /spl Omega//spl middot/cm resistivity on top of a 120 /spl mu/m bulk with 0.03 /spl Omega//spl middot/cm-exhibits a frequency limit of 50MHz below which coupling is insensitive to substrate noise. The difference between experimental results and an analytic model of the line-to-line coupling capacitance ranges from 8.5% to 17.7% for different metal layers.     

Design of wide-band CMOS VCO for multiband wireless LAN applications

In this paper, a general design methodology of low-voltage wide-band voltage-controlled oscillator (VCO) suitable for wireless LAN (WLAN) application is described. The applications of high-quality passives for the resonator are introduced: 1) a single-loop horseshoe inductor with Q > 20 between 2 and 5 GHz for good phase noise performance; and 2) accumulation MOS (AMOS) varactors with C/sub max//C/sub min/ ratio of 6 to provide wide-band tuning capability at low-voltage supply. The adverse effect of AMOS varactors due to high sensitivity is examined. Amendment using bandswitching topology is suggested, and a phase noise improvement of 7 dB is measured to prove the concept. The measured VCO operates on a 1-V supply with a wide tuning range of 58.7% between 3.0 and 5.6 GHz when tuned between /spl plusmn/0.7 V. The phase noise is -120 dBc/Hz at 3.0 GHz, and -114.5 dBc/Hz at 5.6 GHz, with the nominal power dissipation between 2 and 3 mW across the whole tuning range. The best phase noise at 1-MHz offset is -124 dBc/Hz at the frequency of 3 GHz, a supply voltage of 1.4 V, and power dissipation of 8.4 mW. When the supply is reduced to 0.83 V, the VCO dissipates less than 1 mW at 5.6 GHz. Using this design methodology, the feasibility of generating two local oscillator frequencies (2.4-GHz ISM and 5-GHz U-NII) for WLAN transceiver using a single VCO with only one monolithic inductor is demonstrated. The VCO is fabricated in a 0.13-/spl mu/m partially depleted silicon-on-insulator CMOS process.     

Single-pole double-throw CMOS switches for 900-MHz and 2.4-GHz applications on p/sup -/silicon substrates

A 900-MHz single-pole double-throw (SPDT) switch with an insertion loss of 0.5 dB and a 2.4-GHz SPDT switch with an insertion loss of 0.8 dB were implemented using 3.3-V 0.35-/spl mu/m NMOS transistors in a 0.18-/spl mu/m bulk CMOS process utilizing 20-/spl Omega//spl middot/cm p/sup -/ substrates. Impedance transformation was used to reduce the source and load impedances seen by the switch to increase the power handling capability. SPDT switches with 30-/spl Omega/ impedance transformation networks exhibit 0.97-dB insertion loss and 24.3-dBm output P/sub 1dB/ when tuned for 900-MHz operation, and 1.10-dB insertion loss and 20.6-dBm output P/sub 1dB/ when tuned for 2.4-GHz operation. The 2.4-GHz switch is the first bulk CMOS switch which can be used for 802.11b wireless local area network applications.     

A high f/sub OSC//f/sub T/ ratio VCO in SiGe BiCMOS technology

A 37-GHz voltage controlled oscillator (VCO) fabricated in IBM's 47-GHz SiGe BiCMOS technology is presented. The VCO achieves a phase noise of -81dBc/Hz at 1-MHz offset from the carrier while delivering an output power of -30dBm to 50 /spl Omega/ buffers. Drawing 15-mA of dc current from a 3-V power supply the VCO occupies 350/spl mu/m/spl times/280/spl mu/m of silicon area. Capacitive emitter degeneration and compact layout are used to achieve high f/sub OSC//f/sub T/ ratio.     

A 0.35-/spl mu/m CMOS 2-GHz VCO in wafer-level package

This letter presents a complementary metal oxide semiconductor (CMOS) voltage-controlled oscillator (VCO) with a high-Q inductor in a wafer-level package for the LC-resonator. The on-chip inductor is implemented using the redistribution metal layer of the wafer-level package (WLP), and therefore it is called a WLP inductor. Using the thick passivation and copper metallization, the WLP inductor has high quality-factor (Q-factor). A 2-nH inductor exhibits a Q-factor of 8 at 2 GHz. The center frequency of the VCO is 2.16 GHz with a tuning range of 385 MHz (18%). The minimum phase noise is measured to be -120.2 dBc/Hz at an offset frequency of 600 kHz. The dc power consumed by the VCO-core is 1.87 mW with a supply voltage of 1.7 V and a current of 1.1 mA. The output power with a 50-/spl Omega/ load is -12.5/spl plusmn/1.3 dBm throughout the whole tuning range. From the best of our knowledge, compared with recently published 2-GHz-band 0.35 /spl mu/m CMOS VCOs in the literature, the VCO in this work shows the lowest power consumption and the best figure-of-merit.     

5-GHz CMOS LC VCOs with wide tuning ranges

A 4.8-GHz LC voltage-controlled oscillator (VCO) optimized for maximum tuning range was designed and fabricated using 0.25-/spl mu/m 1P5M CMOS process. The optimized design used an inverse proportionality between the two parasitic capacitances of the inductor and the MOS transistors for minimizing the parasitic capacitance at the oscillation node. The fabricated LC VCO has a wide tuning range of 20.3% from 4.32 GHz to 5.3 GHz with a power dissipation of 7.3 mW. This tuning range performance is comparable to, or better than, those of the reported CMOS LC VCOs in 5-GHz band. The measured phase noise is -82 dBc/Hz and -114.6 dBc/Hz at 100 KHz and 1-MHz offset, respectively.     

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer is designed in a standard 0.5 /spl mu/m digital CMOS process for wireless communication. The voltage-controlled oscillator (VCO) required for the low-frequency loop is designed using a ring-type VCO and achieves a tuning range of 89% from 356 to 931 MHz and a phase noise of -109.2 dBc/Hz at 600 kHz offset from 856 MHz. With an active chip area of 2000/spl times/1000 /spl mu/m/sup 2/ and at a 2 V supply voltage, the whole synthesizer achieves a tuning range from 1.8492 to 1.8698 GHz in 200 kHz steps with a measured phase noise of -112 dBc/Hz at 600 kHz offset from 1.86 GHz. The measured settling time is 128 /spl mu/s and the total power consumption is 95 mW.     

A fully integrated 5.8 GHz U-NII band 0.18-/spl mu/m CMOS VCO

A fully integrated 5.8 GHz CMOS L-C tank voltage-controlled oscillator (VCO) using a 0.18-/spl mu/m 1P6M standard CMOS process for 5 GHz U-NII band WLAN application is presented. The VCO core circuit uses only PMOS to pursue a better phase noise performance since it has less 1/f noise than NMOS. The measurement is performed by using a FR-4 PCB test fixture. The output frequency of the VCO is from 5860 to 6026 MHz with a 166 MHz tuning range and the phase noise is -96.9 dBc/Hz at 300 kHz (or -110 dBc/Hz at 1 MHz) with V ctrl = 0 V. The power consumption of the VCO excluding buffer amplifiers is 8.1 mW at V/sub DD/ = 1.8 V and the output power is -4 dBm.     

Modeling, design and characterization of a new low-jitter analog dual tuning LC-VCO PLL architecture

This paper describes the modeling, design, and characterization of a low-jitter 2.4-GHz LC-VCO PLL architecture realized in a standard 0.12-/spl mu/m CMOS technology. It features an analog dual control loop for fine and coarse VCO tuning that allows very low VCO gain (60 MHz/V) for noise rejection while maintaining a wide tuning range. The coarse input of the VCO is driven by an analog circuit that adjusts the VCO gain in a continuous manner. Measurements demonstrate an integrated jitter of 0.74 ps that is 43% lower compared to results from a standard PLL topology (STD PLL) with a single control loop. The PLLs have the same bandwidth and output frequency range and were built on the same wafer for comparison. The circuit area of the proposed LC-VCO PLL is 0.7 mm/sup 2/ and the power consumption is 32 mW. The area and power consumption of the proposed LC-VCO PLL are less than 1% larger compared to the STD PLL.     

Low phase noise IP VCO for multistandard communication using a 0.35-/spl mu/m BiCMOS SiGe technology

In this letter, we report that a commonly used 0.35-/spl mu/m, 60-GHz-F/sub MAX/ BiCMOS SiGe monolithic microwave integrated circuit (MMIC) technology is able to provide very low phase noise signal generation in the X-band frequency range. This statement has been demonstrated using a differential LC voltage-controlled oscillator (VCO) in which varactors are realized with metal-oxide semiconductor (MOS) transistors and inductors with a patterned ground shield technology. This VCO features an output power signal in the range of -5 dBm and exhibits a phase noise of -96 dBc/Hz at a frequency offset of 100kHz from carrier and -120 dBc/Hz at a frequency offset of 1 MHz. The VCO features a tuning range of 430 MHz or 4.3% of its operating frequency. Its power consumption is in the range of 70 mW (200 mW with buffers circuits) for a chip size of 800/spl times/1000 /spl mu/m/sup 2/ (including RF probe pads).     

A low-power oscillator mixer in 0.18-/spl mu/m CMOS technology

A downconversion double-balanced oscillator mixer using 0.18-/spl mu/m CMOS technology is proposed in this paper. This oscillator mixer consists of an individual mixer stacked on a voltage-controlled oscillator (VCO). The stacked structure allows entire mixer current to be reused by the VCO cross-coupled pair to reduce the total current consumption of the individual VCO and mixer. Using individual supply voltages and eliminating the tail current source, the stacked topology requires 1.0-V low supply voltage. The oscillator mixer achieves a voltage conversion gain of 10.9 dB at 4.2-GHz RF frequency. The oscillator mixer exhibits a tuning range of 11.5% and a single-sideband noise figure of 14.5 dB. The dc power consumption is 0.2 mW for the mixer and 2.94 mW for the VCO. This oscillator mixer requires a lower supply voltage and achieves a higher operating frequency among recently reported Si-based self-oscillating mixers and mixer oscillators. The mixer in this oscillator mixer also achieves a low power consumption compared with recently reported low-power mixers.     

A 0.83-2.5-GHz continuously tunable quadrature VCO

A quadrature VCO with /spl plusmn/50% continuous 0.83-2.5-GHz tuning range is presented. It is based on a core LC-QVCO with /spl plusmn/20% tuning range, a single sideband mixer (SSBM), two frequency dividers and a multiplexer. The circuit has been implemented in a 0.13-/spl mu/m 1.2-V CMOS technology. The additional area with respect to the core LC-QVCO is 100 /spl mu/m/spl times/100 /spl mu/m. Quadrature error is less than 2/spl deg/; the phase noise is less than -120 dBc/Hz @ 1 MHz over the whole tuning range and is mainly due to the LC-QVCO. Spurs are more than 34 dB below the fundamental in the worst case.     

A low-phase-noise K-band CMOS VCO

A novel circuit topology for low-phase-noise voltage controlled oscillators (VCOs) is presented in this letter. By employing a PMOS cross-coupled pair with a capacitive feedback, superior circuit performance can be achieved especially at higher frequencies. Based on the proposed architecture, a prototype VCO implemented in a 0.18-/spl mu/m CMOS process is demonstrated for K-band applications. From the measurement results, the VCO exhibits a 510-MHz frequency tuning range at 20GHz. The output power and the phase noise at 1-MHz offset are -3dBm and -111dBc/Hz, respectively. The fabricated circuit consumes a dc power of 32mW from a 1.8-V supply voltage.     

A 4-91-GHz traveling-wave amplifier in a standard 0.12-/spl mu/m SOI CMOS microprocessor technology

This paper presents five-stage and seven-stage traveling-wave amplifiers (TWA) in a 0.12-/spl mu/m SOI CMOS technology. The five-stage TWA has a 4-91-GHz bandpass frequency with a gain of 5 dB. The seven-stage TWA has a 5-86-GHz bandpass frequency with a gain of 9 dB. The seven-stage TWA has a measured 18-GHz noise figure, output 1-dB compression point, and output third-order intercept point of 5.5 dB, 10 dBm, and 15.5 dBm, respectively. The power consumption is 90 and 130 mW for the five-stage and seven-stage TWA, respectively, at a voltage power supply of 2.6 V. The chips occupy an area of less than 0.82 and 1 mm for the five-stage and seven-stage TWA, respectively.     

A 15/30-GHz Dual-Band Multiphase Voltage-Controlled Oscillator in 0.18- μm CMOS

A multiphase oscillator suitable for 15/30-GHz dual-band applications is presented. In the circuit implementation, the 15-GHz half-quadrature voltage-controlled oscillator (VCO) is realized by a rotary traveling-wave oscillator, while frequency doublers are adopted to generate the quadrature output signals at the 30-GHz frequency band. The proposed circuit is fabricated in a standard 0.18-mum CMOS process with a chip area of 1.1times1.0 mm². Operated at a 2-V supply voltage, the VCO core consumes a dc power of 52 mW. With a frequency tuning range of 250 MHz, the 15-GHz half-quadrature VCO exhibits an output power of -8 dBm and a phase noise of -112 dBc/Hz at 1-MHz offset frequency. The measured power level and phase noise of the 30-GHz quadrature outputs are -16 dBm and -104 dBc/Hz, respectively     

A low-phase-noise and low-power multiband CMOS voltage-controlled oscillator

A low voltage multiband all-pMOS VCO was fabricated in a 0.18-/spl mu/m CMOS process. By using a combination of inductor and capacitor switching, four band (2.4, 2.5, 4.7, and 5 GHz) operation was realized using a single VCO. The VCO with an 1-V power supply has phase noises at 1-MHz offset from a 4.7-GHz carrier of -126 dBc/Hz and -134 dBc/Hz from a 2.4-GHz carrier. The VCO consumes 4.6 mW at 2.4 and 2.5 GHz, and 6 mW at 4.7 and 5 GHz, respectively. At 4.7 GHz, the VCO also achieves -80 dBc/Hz phase noise at 10-kHz offset with 2 mW power consumption.     

A 1.8-GHz LC VCO with 1.3-GHz tuning range and digital amplitude calibration

A 1.8-GHz LC VCO designed in a 0.18-/spl mu/m CMOS process achieves a very wide tuning range of 73% and measured phase noise of -123.5 dBc/Hz at a 600-kHz offset from a 1.8-GHz carrier while drawing 3.2 mA from a 1.5-V supply. The impacts of wideband operation on start-up constraints and phase noise are discussed. Tuning range is analyzed in terms of fundamental dimensionless design parameters yielding useful design equations. An amplitude calibration technique is used to stabilize performance across the wide band of operation. This amplitude control scheme not only consumes negligible power and area without degrading the phase noise, but also proves to be instrumental in sustaining the VCO performance in the upper end of the frequency range.