Refining the phase diagram of PbZr1−x−ySnxTiyO3 ceramics with 0.40≤x≤0.54 by crystal structural,dielectric response and hysteresis loop investigations

Ceramics of PbZr_1−x−ySn_xTi_yO₃ (PZST100x/100y) with 0.40≤x≤0.54 were synthesized via conventional solid state reaction and their crystal structures, dielectric response, and hysteresis loops were systematically investigated. A more precise range of the antiferroelectric/ferroelectric phase boundary of PZST100x/100y ceramics with 0.40≤x≤0.54 was established compared with the results reported by Jaffe. It was found that the introduction of Ti⁴⁺stabilized the ferroelectric order, and Sn⁴⁺substitution enhanced the antiferroelectric order. Thus, the system properties could be tailored by altering Sn and Ti concentration. In addition, the hydrostatic pressure-induced ferroelectric-to-antiferroelectric phase transition was also studied. It has been clarified that the critical transition pressure (P_t) increased with an increasing Ti content at a fixed Sn content.     

Thermal characterization of Se78 − x Te20Sn2Pb x (0 ≤ x ≤ 6) glassies for phase change optical recording technique

New multi-component glasses of Se_{78 ? x} Te₂₀Sn₂Pb _x (0 ≤ x ≤ 6) system have been synthesized using melt-quench technique. Differential Scanning Calorimetric measurements are performed at different heating rates under non-isothermal conditions to study the glass transition kinetics of prepared chalcogenide glass. Different kinetic parameters such as the activation energy of glass transition, thermal stability, glass forming ability etc have been determined. The composition dependence of kinetic parameters of glass transition is also discussed.     

Structural,magnetic and magnetocaloric properties of CoFe2−xMoxO4 (0.0≤x≤0.3) ferrites

We have investigated structural, magnetic and magnetocaloric properties of CoFe_2-xMo_xO₄ (0.0≤x≤0.3) ferrites. Polycrystalline samples were prepared by the sol gel method and characterized by the powder X-ray diffraction and scanning electron microscopy. X-ray diffraction patterns show that all samples have a cubic spinel structure and the lattice parameter, a, decreases monotonically with increase in Mo concentration. Scanning electron micrographs indicate that most of the particles are in the range of 400–850 nm size. Magnetic measurements, performed by using a cryogen free vibrating sample magnetometer, show that these samples are soft ferromagnets in the measured temperature range. The saturation magnetization, M_s, values of Mo-doped samples are larger than the parent compound with a maximum value of ~106 emu/g for x=0.2 sample. The magnetic entropy change (−ΔS) increases with increase in applied magnetic field and shows a peak in the vicinity of blocking temperature. A maximum value of 0.56 J kg⁻¹ K⁻¹ at 5 T field has been observed for x=0.2 sample.     

Origin of anomalous octahedral distortions and collapse of magnetic ordering in Nd1−xSrxFeO3 (0≤x≤0.5)

The effects of strontium doping on the structural properties and magnetic ordering of Nd_1?xSr_xFeO₃ orthoferrite system have been studied by employing macroscopic and microscopic structural techniques like X-ray diffraction, scanning electron microscopy and ⁵⁷Fe Mössbauer spectroscopy. X-ray diffraction confirmed that single phase materials have been synthesized. It has been observed that orthorhombic distortion, density and porosity have decreased; whereas, grain size, tolerance factor and symmetry have increased with increase in the strontium concentration. Mössbauer results showed an increase in the Fe⁴⁺/Fe³⁺ ratio, sagging and local octahedral distortions while decrease in the magnetic ordering with increase in the strontium content. The origin behind anomalous octahedral distortions in this system has been attributed to the decrease in the oxidation state and mismatch in the ionic radii of A-site cations and increase in the concentration of Fe⁴⁺, due to Sr²⁺ doping at Nd³⁺ sites. The collapse of magnetic ordering has been ascribed to the weakening of super-exchange interactions, dilution of strong long range magnetic sub-lattice of high spin Fe³⁺ (five unpaired electrons) by relatively lower spin of high spin Fe⁴⁺ (four unpaired electrons) and increase in the spin–spin relaxation frequency.     

Synthesis,characterization and catalytic properties of La2−x Sr x NiO4−δ

Various compositionsx in the catalyst system La_2–x Sr _x NiO_4– have been prepared by conventional techniques and characterized by X-ray powder diffraction, electron microscopy and BET surface measurements. The catalytic properties of these catalysts have been tested in the propylene oxidation reaction. The catalytic activity can be correlated with the oxygen content and with the strontium substitution.     

Finite size effect on Sm3+ doped Mn0.5Zn0.5SmxFe2−xO4 (0≤x≤0.5) ferrite nanoparticles

Samarium doped Mn–Zn ferrite nanoparticles of composition Mn_0.5Zn_0.5Sm_xFe_2−xO₄ (0≤x≤0.5) have been synthesized by a chemical co-precipitation method for developing low Curie temperature stable ferrofluid. These samples were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy Dispersive Spectroscopy (EDS), Electron Paramagnetic Resonance (EPR) spectroscopy and search coil method analytical techniques for their structural, morphological and magnetic properties. X-ray diffraction patterns confirmed the formation of crystalline single spinel phase of as grown nanoparticles. Lattice parameter and lattice strain increases with the increase in Sm³⁺ content. SEM images revealed the presence of ultrafine particles and their agglomerated structures in higher Sm³⁺ ions concentration analogues. The stoichiometry of the final product agreed well with the initial substitution composition as evidenced by EDS data. Electron paramagnetic resonance (EPR) spectra proved the ferromagnetic nature of nanoparticles. The magnetic measurements by search coil method showed superparamagnetism for x=0, 0.1 the samples with saturation magnetization of 23.95 emu/g for Mn_0.5Zn_0.5Fe₂O₄ sample which increases with rise in Sm³⁺ ions content. The results are explained and correlated with the structural, morphological and magnetic properties for developing stable kerosene based ferrofluid by using these nanoparticles.     

Synthesis,sintering, and thermoelectric properties of Co1-xMxO (M = Na, 0 ≤ x ≤ 0.07; M = Ag, 0 ≤ x ≤ 0.05)

The structural and thermoelectric properties of Na- and Ag-substituted CoO dense ceramics have been investigated. X-ray diffraction shows that pure phase and Ag/CoO composites have been obtained for Na-doped and Ag-doped CoO, respectively. Raman spectroscopy shows an effect of Na dopants on the lattice disorder of CoO. The chemical composition, element distribution, and valence states of the samples have been characterized by Auger electron microscopy and X-ray photoelectron spectroscopy. Substitution of Co by 5 at. % Na enhances the power factor to 250 μW m⁻¹ K^-2 at 1000 K, similar to that of Ca₃Co₄O₉. The corresponding thermal conductivity is also reduced to 3.55 W.m⁻¹ K⁻¹ at 1000 K. Consequently, Co_0.95Na_0.05O exhibits the best thermoelectric figure of merit (ZT), which is 0.07 at 1000 K. On the other hand, the substitution of Ag into CoO leads to the formation of CoO/Ag composites and deteriorates ZT values.     

Magnetic properties of ferrites-cobaltites Bi1 − x La x Fe1 − x Co x O3 (1.0 ≥ x ≥ 0.7) with a perovskite structure

The molar magnetic susceptibility (χ_mol) of Bi_{1 ? x} La _x Fe_{1 ? x} Co _x O₃ solid solutions (x = 1.0, 0.9, 0.8, or 0.7) with a crystal structure of rhombohedrally distorted perovskite (R $\bar 3$ c) has been investigated in the temperature range of 5–300 K in a 0.86 T magnetic field. In the temperature range where χ_mol depends on temperature T according to the Curie-Weiss law, the resulting effective magnetic moments of Fe³⁺ and Co³⁺ ions ( $\mu _{eff,Fe^{3 + } ,Co^{3 + } ,} \mu _{eff,Fe^{3 + } } $ and $\mu _{eff,Co^{3 + } } $ ) have been determined for the solid solutions under study. Fe³⁺ ions in the solid solutions have been found to be in the mixed intermediate spin (IS) and high spin (HS) states ( $\mu _{eff,Fe^{3 + } } $ is 4.26μ_B and 4.68μ_B for the temperature range of 5–100 and 150–300 K, respectively). It is shown that 8% Co³⁺ ions in LaCoO₃ at 5–19 K are in the paramagnetic IS state and they determine to a great extent the magnetic susceptibility. It is established that only 9% and 18% Co³⁺ ions in Bi_{1 ? x} La _x Fe_{1 ? x} Co _x O₃ solid solutions (x = 0.9 or 0.8) are in the paramagnetic IS state in the temperature ranges of 5–30 and 5–110 K, respectively, while the other ions are diamagnetic.     

Surface Exchange of Oxygen in La1−x Sr x FeO3−δ (x = 0, 0.1)

The electronic charge carrier concentration in La_1?x Sr _x FeO_3?δ was shown to depend on the partial pressure of O₂ (pO ₂). Chemical diffusion coefficient and surface exchange coefficient, k _chem, were determined by conductivity relaxation in O₂/N₂ and CO/CO₂ mixtures. k _chem was proportional to pO ₂ ^1.06 in O₂/N₂, while in CO/CO₂ k _chem was controlled by a reaction mechanism involving both CO and CO₂.     

Studies on NO2 gas sensing properties of sprayed Co1−xMnxFe2O4 (0≤x≤0.5) spinel ferrite thin films

The Co_1−xMn_xFe₂O₄ (0≤x≤0.5) spinel ferrite thin films were deposited on quartz substrates by chemical spray pyrolysis technique. The effect of Mn substitution on to the structural, electrical, dielectric and NO₂ gas sensing properties of cobalt ferrite thin films was studied. The X-ray diffraction analysis reveals that deposited films exhibit spinel cubic crystal structure. The lattice constant increases with the increase in Mn²⁺ content. The decrease in resistivity with increase in temperature suggests that the films have a semiconducting nature. The room temperature dielectric properties such as dielectric constant (ε′), loss tangent (tanδ), dielectric loss (ε′′) and AC conductivity have been studied in the frequency range 20 Hz–1 MHz. The film shows the highest sensor response at moderately low (150 °C) operating temperature. The effect of operating temperature, gas concentration, film selectivity and substitution of Mn on to gas response is carefully studied. The manganese substituted cobalt ferrite films are extremely selective towards NO₂ with a 20 times gas response compared with other gases. The gas response achieved nearly 92% of its initial value after 150 days, indicating good stability of the films.     

Physicochemical and electrochemical performance of LiFe1−xNixPO4 (0≤x≤1.0) solid solution as potential cathode material for rechargeable lithium-ion battery

In this work, olivine-type LiFePO₄ (LFP) and nickel (Ni) substituted LiFe_1-xNi_xPO₄ (0≤ x≤1.0) solid solutions were synthesized using the wet-milling route. Synthesized samples were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). XRD results show that all the samples were crystallized in the orthorhombic phase with Pnma space group and no secondary phase was detected even at higher Ni-concentration. Rietveld refinement results reveal that average <Li-O> distance increases up to x=0.03 (LFNP3) and decrease thereafter monotonically on further increase in Ni-concentration. Moreover, the LFNP3 sample shows highest electrical conductivity as compared to other solid solutions. Among the synthesized samples for x≤0.1, LFNP3 shows highest discharge capacity at all C-rates. LFNP3 exhibits a discharge capacity of 158 (±5) mAh g⁻¹ at 0.1 C (almost 93% of the theoretical capacity) and displays the high and stable discharge capacity of 145 (±5) mAh g⁻¹ at 1 C rate for 150 charge/discharge cycles. Among high Ni content (0.1< x≤1.0) samples, LiFe_0.7Ni_0.3PO₄ (LFNP30) delivers best charge/discharge capacity at all C-rates. LFNP30 exhibits a discharge capacity of 90 (±5) mAh g⁻¹ at 0.1 C rate.     

Influence of La addition on the structural,magnetic and magnetocaloric properties in Sr2−xLaxFeMoO6 (0≤x≤0.3) double perovskite

We report the effect of carrier doping via partial substitution of La³⁺ for Sr²⁺ on the structural, magnetic and magnetocaloric properties of Sr₂FeMoO₆ double perovskite. Polycrystalline Sr_2−xLa_xFeMoO₆ (x=0.0, 0.1, 0.2, 0.3) samples were prepared using the conventional solid state reaction method. Using the X-ray diffraction (XRD) analysis it was established that all the samples crystallized in a tetragonal structure with I4/mmm space group. An increase in the La doping lead to an increase in the lattice parameter ‘a’ and the volume of the unit cell. The lattice parameter ‘c’ however remained unchanged. The temperature variation in magnetization and Arrott analysis suggested a second order of ferromagnetic phase transition in all samples with Curie temperature, T_C increasing from 358 K for x=0.0–365 K for x=0.3. A gradual increase in magnetization was also observed with the increasing La content up to x=0.2. The magnetic entropy change was calculated from the measurement of isothermal magnetization versus magnetic field at different temperatures. The tunability of magnetization and T_C simply by adjusting the concentration of La and synthesis conditions makes Sr₂FeMoO₆ an attractive material for magnetic refrigeration at desired temperature.     

Electrochemical evaluation of LiZnxMn2−xO4 (x≤0.10) cathode material synthesized by solution combustion method

The spinel LiZn_xMn_2−xO₄ (x≤0.10) cathode materials have been synthesized by solution combustion method at 600 °C for 3 h. The structure and the morphology of LiZn_xMn_2−xO₄ were characterized by X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM), respectively. All the obtained samples were identified as the spinel structure of LiMn₂O₄, the lattice parameters of samples decreased and the particle size increased as the Zn content increased. The effects of Zn-doping on the electrochemical characteristics of LiMn₂O₄ were investigated by galvanostatic charge–discharge experiments, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Among them, LiZn_0.05Mn_1.95O₄ particles presented outstanding cycling stability with a capacity retention of 82.9% at a discharge rate of 1 C (1 C=148 mA h g⁻¹) after 500 cycles. Spinel LiZn_0.05Mn_1.95O₄ had reversible cycling performance, revealing that doping LiMn₂O₄ with Zn improves its electrochemical performance.     

Synthesis and characterisation of MnGaxCr2−xO4 (0.1≤x≤1) spinels as potential electrode support materials for intermediate-temperature solid oxide fuel cells

MnGa_xCr_2−xO₄ (MGCO, x=0.1, 0.2, 0.4, 0.8, 1) oxides are synthesised using a citric acid nitrate combustion method. The influence of Ga substitution on the structure, electrical conductivity and electrochemical performance are systematically investigated. The chemical and thermal compatibility of MGCO materials with yttrium-stabilised zirconia (YSZ) are also studied. All the samples exhibit a single phase spinel structure. Thermal expansion coefficients (TECs) of the MGCO oxides are in the range of 9–12×10⁻⁶ K⁻¹, indicating a good thermal match with the YSZ electrolyte. No chemical reactions are detected between MGCO materials and YSZ, indicating their good chemical compatibility with YSZ. The magnitude of electrical conductivity of all the obtained samples is in the order of about 10⁻³ S cm⁻¹at 800 °C measured in air. The polarisation resistance reaches a value as low as 5.2 Ω cm² for x=0.4 at 800 °C. The preliminary results demonstrate that MGCO materials could be used as electrode support materials for intermediate-temperature solid oxide fuel cells (IT-SOFCs).     

Perovskite forming ceramics of the system SrxLa1−x TiIVx+yCoIIyCoIII1−x−2yO3 for NTC thermistor applications

The paper reports the preparation, structure and electrical properties of oxide ceramic semiconductors based on the series Sr_xLa_1−x Ti^IV_x+yCo^II_yCo^III_1−x−2yO₃ with perovskite type stucture: 0<x<1, 0<y<(1−x)/2. The study starts from LaCoO₃ which is highly conductive yielding metallic condutivity above 330°C. The upset trigonal distortion of LaCoO₃ is reduced when Sr^II/Ti^IV is substituted for La^III/Co^III corresponding to increasing values of x and also when 2 Co^III are introduced for Ti^IV/Co^II into the lattice corresponding to increasing values of y. At high values of x and y othorhombic distortion occurs. At the same time, the interaction between the Co^III atoms of LaCoO₃ is increasingly interrupted providing increasing values of the the resistivity value ρ_25°C and of the B_25/100°C value deduced from measurements at 25 and 100°C according to ρ(T )=ρ_25°C e^B/T. The range of variation of x an y makes possible to prepare ceramics with desired electrical properties within the limits of ρ_25°C=1.1 Ωcm, B=1910 K and ρ_25°C=1 bis 8×10⁶ Ωcm at B-values up to 6500 K. Dependent on composition, NTC ceramics for thermistor or insurance applications are accessible. Thermistors do not show aging even at higher temperature, e.g. at 500°C, provided the single phase state is achieved as a result of mixed oxide preparation and sintering. Hence, high temperature thermistor applications are also made possible. The semiconductor behavior can be understood using the conventional polaron state hopping model.     

Thermoelectric properties of copper-deficient Cu2-xSe (0.05 ≤ x ≤ 0.25) binary compounds

Recently, many novel superionic thermoelectric materials have been discovered along the concept of “phonon-liquid electron-crystal” (PLEC). Among them, Cu_2-xSe-based liquid-like materials are typical examples. In this study, a series of copper-deficient Cu_2-xSe (0.05 ≤ x ≤ 0.25) materials were synthesized and used to study the role of Cu vacancies on the electrical and thermal transport properties. The X-ray photoelectron spectroscopy (XPS) measurements suggest that the valence states of Cu and Se are independent on the Cu/Se atomic ratio. With increasing the content of Cu vacancies, the hole concentration is monotonously increased, leading to the improved electrical conductivity and reduced Seebeck coefficient. Based on the single parabolic band model analysis, it is found that changing the content of Cu vacancies does not obviously modify the material's electronic band structure and effective mass. Due to the presence of highly mobile Cu ions inside the crystal structure, the lattice thermal conductivities of all Cu_2-xSe (0.05 ≤ x ≤ 0.25) materials are very low with values around 0.39 W m⁻¹ K⁻¹ at 500 K. Because of the significantly reduced Seebeck coefficient and increased electronic thermal conductivity, the thermoelectric figure of merit zTs are decreased when increasing x from 0.05 to 0.25. At 750 K, a maximum zT of 0.46 is obtained in Cu_1.95Se among all Cu_2-xSe (0.05 ≤ x ≤ 0.25) materials.     

Nonstoichiometry in perovskite-type oxide Ca1−x Ce x MnO3−δ and its properties in alkaline solution

Nonstoichiometry in high conductivity perovskite-type oxide Ca_1-x Ce _x MnO_3- was investigated. At room temperature in air, the 3- value was determined to be 2.91 for CaMnO_3-, which meant that 82% of manganese was tetravalent. Although the 3- value increased by increasing the cerium content, i.e. by doping of higher valent cation into the calcium site, the quantity of Mn⁴⁺ in the sample oxide essentially decreased with increasingx. The oxygen contents change reversibly with temperature in air. Change of oxygen content was also observed on discharging this oxide as the cathode material of a battery in alkaline solution. Surprisingly, the sintered ceramics of this oxide worked as a cathode without mixing with a conductive powder such as graphite. Considering the discharging performance, this oxide may be a candidate for the cathode material of the alkaline battery.     

Li1-xTixFePO4(O≤x≤0.02)制备表征及电化学性能研究

采用固相工艺制备了具有锂位掺杂的磷酸铁锂正极材料Li1-xTixFePO4(0≤x≤0.02),并将该材料与相同条件下制备的LiFePO4/C材料进行晶体结构、表面形貌、容量性能以及倍率性能比较.通过比较发现,Li1-xTixFePO4和LiFePOJC均具有橄榄石结构,且粒径大小均在2～4 μn.电化学性能测试结果表明,Li1-xTixFePO4比LiFePO4/C具有更加优异的容量性能和倍率性能.