基于非局部弹性理论的单壁碳纳米管轴向受压屈曲研究

基于非局部弹性理论，在考虑小尺度效应影响的情况下，建立了单壁碳纳米管在均匀轴向外 部压力下的壳体模型. 得到了单壁碳纳米管的轴向受压屈曲的临界条件，验证了小尺度效应 对纳米管轴向受压屈曲的影响. 经典的壳体模型理论由于没有考虑小尺度效应影响而导致碳 纳米管轴向屈曲临界压力值偏高. 关键词： 非局部弹性理论 碳钠米管 小尺度效应 轴向受压     

单壁碳纳米管轴向压缩变形的研究

采用Tersoff-Brenner势函数描述碳纳米管中碳原子间的相互作用，通过分子动力学方法对不同螺旋型的单壁碳纳米管的轴向压缩变形行为进行了研究.研究发现单臂碳纳米管的杨氏模量低于锯齿形碳纳米管，根据微观结构特征的差异对这一结果进行了分析.同时从能量和结构变化两方面对碳纳米管受压失稳进行了分析，揭示出碳纳米管失稳的微观特征. 关键词： 纳米管 分子动力学 杨氏模量 屈曲     

碳纳米管的近边吸收谱研究

用X射线近边吸收谱研究了单壁, 双壁和多壁碳纳米管在超高真空系统中不同温度下退火处理后的行为.碳的K边吸收谱表明, 多壁管上吸附的杂质将在热处理过程中最先被去除, 其次是双壁管, 最后是单壁管.这种热处理下杂质去除的顺序说明了曲率越小杂质吸附得越牢靠, 即越容易吸附杂质.另外, 结果中显示, 经退火处理后3种碳纳米管在多重散射区域的峰结构呈现规律性的移动,由单壁管到多壁管, 谱峰向低能方向移动; 这是由于碳纳米管的层数不同造成的, 证明这部分谱峰结构直接受到碳纳米管层数的调制, 有利于鉴别3种碳纳米管.     

Rh在单壁碳纳米管上吸附的密度泛函理论研究

本文利用密度泛函理论研究了Rh原子在（6,6）单壁碳纳米管内外的吸附行为. 通过对Rh在单壁碳纳米管上不同吸附位的吸附构型与吸附能的研究发现: Rh吸附在管内、外的洞位最稳定, 且管外吸附比在管内强. 这是由于单壁碳纳米管的卷曲效应使得管外电荷密度比管内大造成的. 态密度分析表明, 吸附在管内外的Rh原子的5s电子均转移到了4d轨道上; Rh原子4d轨道上的电子转移到了（6, 6）碳管上, 使Rh带正电, 碳管带负电. 结合能带分析表明, Rh原子吸附在管内磁性较弱, 而吸附在管外较强. 关键词： 密度泛函理论 单壁碳纳米管 Rh原子 吸附     

范德华力对双壁碳纳米管轴向压缩屈曲行为的影响

使用分子动力学方法研究几种不同半径尺寸的单壁碳纳米管组成的双壁碳管，预测了其初始稳定构型；分析了其自由弛豫阶段的特征；并模拟了它们在轴向压缩载荷作用下的屈曲行为；研究了不同层间距导致的范德华力变化对屈曲行为的影响.采用Tersoff-Brenner势描述单壁碳纳米管内原子间作用，Lennard-Jones势描述内外层间的范德华相互作用.计算结果表明：在通常意义下的双壁管间距(约0.34 nm)外还可以存在稳定的双壁碳管构型，并且这些新的稳定构型表现出了不同的力学性质. 关键词： 双壁碳纳米管 分子动力学 屈曲     

单壁碳纳米管非线性力学行为的数值模拟

单壁碳纳米管的力学行为是纳米复合材料和纳米器械的基本问题之一.使用有限元方法系统地研究了单壁碳纳米管的轴压和纯弯变形,并将有限元模拟结果和分子动力学模拟结果进行了比较.研究结果表明单壁碳纳米管的轴压屈曲载荷受直径变化的影响;单壁碳纳米管在弯曲载荷作用下的屈曲和后屈曲行为强烈地依赖于管长和管径的变化,合理地选择碳纳米管的弹性模量和壁厚,有限元方法能够很好地解释碳纳米管的屈曲机理.研究大尺度的纳米力学问题时,有限元方法将会成为更加准确、快捷的数值模拟方法. 关键词： 单壁碳纳米管 非线性力学行为 有限元     

碳纳米锥力学特性的分子动力学研究

结合原子间短程作用势(Brenner势)和长程作用势(Lennard-Jones势),利用分子动力学方法对各种锥角的碳纳米锥进行拉伸和压缩实验,获得其载荷-应变关系曲线、受拉/压载荷极限、应变极限和构形演变等力学特性,并与等量原子组成的碳纳米管进行比较研究.研究结果表明,等量碳原子组成的碳纳米锥的受拉/压载荷极限随着锥角的增大先是增大后减小,受拉/压应变极限则随着锥角的增大而增大.与碳纳米锥相比,等量碳原子组成的碳纳米管的受拉/压载荷极限和应变极限显得既不突出也不逊色.在受压构形演化方面,与碳纳米管丰富的径向屈曲/扭转/侧向屈曲组合形变不同,112.88°和83.62°锥角的碳纳米锥受压沿轴向完美内陷,而60.0°和38.94°锥角的碳纳米锥受压发生侧向屈曲.     

热力耦合作用下双层碳纳米管的扭转屈曲

考虑碳纳米管周边弹性介质和层间范德瓦耳斯力的作用,利用连续介质力学的壳体理论,建立了热力耦合作用下碳纳米管屈曲问题的控制方程,给出了相应的临界屈曲扭矩的解析解.数值模拟结果表明,在低温和室温环境下,碳纳米管的临界屈曲载荷随着温度变化量的增加而提高;在高温环境下,碳纳米管的临界屈曲载荷随着温度变化量的增加而降低. 关键词： 碳纳米管 屈曲 热力耦合     

轴向冲击载荷作用下双壁碳纳米管的动力屈曲

应用改进的有限元方法,建立考虑层间范德华力作用的壳-弹簧非线性有限元模型,基于B-R运动准则,系统地研究了双壁碳纳米管的动力屈曲问题,得到了轴向冲击载荷作用下双壁碳纳米管的临界动力屈曲载荷和临界动力失效载荷. 研究结果表明,在动力屈曲过程中,双壁碳纳米管层间距的变化非常小,各管的变形相互协调;碳纳米管中应力波的传播导致碳纳米管出现非对称屈曲模态,可明显观测到四个环向波瓣,沿着碳纳米管的轴线方向,四个波瓣的波峰和波谷交替变化. 对碳纳米管动力屈曲问题的研究表明,冲击载荷的大小和持续时间对碳纳米管的动力屈曲有 关键词： 碳纳米管 动力屈曲 冲击载荷     

单壁碳纳米管非线性力学行为的数值模拟

单壁碳纳米管的力学行为是纳米复合材料和纳米器械的基本问题之一.使用有限元方法系统地研究了单壁碳纳米管的轴压和纯弯变形，并将有限元模拟结果和分子动力学模拟结果进行了比较.研究结果表明单壁碳纳米管的轴压屈曲载荷受直径变化的影响；单壁碳纳米管在弯曲载荷作用下的屈曲和后屈曲行为强烈地依赖于管长和管径的变化，合理地选择碳纳米管的弹性模量和壁厚，有限元方法能够很好地解释碳纳米管的屈曲机理.研究大尺度的纳米力学问题时，有限元方法将会成为更加准确、快捷的数值模拟方法.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.