A Comparative NBTI Study of $hbox{HfO}_{2}$, $hbox{HfSiO}_{x}$, and SiON p-MOSFETs Using UF-OTF $I_{rm DLIN}$ Technique

The time, temperature, and oxide-field dependence of negative-bias temperature instability is studied in $hbox{HfO}_{2}/hbox{TiN}$, $ hbox{HfSiO}_{x}/hbox{TiN}$, and SiON/poly-Si p-MOSFETs using ultrafast on-the-fly $I_{rm DLIN}$ technique capable of providing measured degradation from very short (approximately microseconds) to long stress time. Similar to rapid thermal nitrided oxide (RTNO) SiON, $hbox{HfO}_{2}$ devices show very high temperature-independent degradation at short (submilliseconds) stress time, not observed for plasma nitrided oxide (PNO) SiON and $hbox{HfSiO}_{x}$ devices. $hbox{HfSiO}_{x}$ shows lower overall degradation, higher long-time power-law exponent, field acceleration, and temperature activation as compared to $hbox{HfO}_{2}$, which are similar to the differences between PNO and RTNO SiON devices, respectively. The difference between $ hbox{HfSiO}_{x}$ and $hbox{HfO}_{2}$ can be attributed to differences in N density in the $hbox{SiO}_{2}$ IL of these devices.      

High-Performance Poly-Silicon TFTs Using a High-$k$ $hbox{PrTiO}_{3}$ Gate Dielectric

In this letter, a polycrystalline-silicon thin-film transistor (poly-Si TFT) with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is proposed for the first time. Compared to TFTs with a $hbox{Pr}_{2}hbox{O}_{3}$ gate dielectric, the electrical characteristics of poly-Si TFTs with a $hbox{PrTiO}_{3}$ gate dielectric can be significantly improved, such as lower threshold voltage, smaller subthreshold swing, higher $I_{rm on}/I_{rm off}$ current ratio, and larger field-effect mobility, even without any hydrogenation treatment. These improvements can be attributed to the high gate capacitance density and low grain-boundary trap state. All of these results suggest that the poly-Si TFT with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is a good candidate for high-speed and low-power display driving circuit applications in flat-panel displays.      

High-Performance $hbox{In}_{0.7}hbox{Ga}_{0.3}hbox{As}$ -Channel MOSFETs With High-$kappa$ Gate Dielectrics and $alpha$-Si Passivation

Long and short buried-channel $hbox{In}_{0.7}hbox{Ga}_{0.3}hbox{As}$ MOSFETs with and without $alpha$-Si passivation are demonstrated. Devices with $alpha$-Si passivation show much higher transconductance and an effective peak mobility of 3810 $hbox{cm}^{2}/ hbox{V} cdot hbox{s}$. Short-channel MOSFETs with a gate length of 160 nm display a current of 825 $muhbox{A}/muhbox{m}$ at $V_{g} - V_{t} = hbox{1.6} hbox{V}$ and peak transconductance of 715 $muhbox{S}/muhbox{m}$. In addition, the virtual source velocity extracted from the short-channel devices is 1.4–1.7 times higher than that of Si MOSFETs. These results indicate that the high-performance $hbox{In}_{0.7}hbox{Ga}_{0.3} hbox{As}$-channel MOSFETs passivated by an $alpha$ -Si layer are promising candidates for advanced post-Si CMOS applications.      

Performance Improvement of N-Type $hbox{TiO}_{x}$ Active-Channel TFTs Grown by Low-Temperature Plasma-Enhanced ALD

We report on performance improvement of $n$-type oxide–semiconductor thin-film transistors (TFTs) based on $hbox{TiO}_{x}$ active channels grown at 250 $^{circ}hbox{C}$ by plasma-enhanced atomic layer deposition. TFTs with as-grown $hbox{TiO}_{x}$ films exhibited the saturation mobility $(mu_{rm sat})$ as high as 3.2 $hbox{cm}^{2}/hbox{V}cdothbox{s}$ but suffered from the low on–off ratio $(I_{rm ON}/I_{rm OFF})$ of $hbox{2.0} times hbox{10}^{2}$. $hbox{N}_{2}hbox{O}$ plasma treatment was then attempted to improve $I_{rm ON}/I_{rm OFF}$. Upon treatment, the $hbox{TiO}_{x}$ TFTs exhibited $I_{rm ON}/I_{rm OFF}$ of $hbox{4.7} times hbox{10}^{5}$ and $mu_{rm sat}$ of 1.64 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, showing a much improved performance balance and, thus, demonstrating their potentials for a wide variety of applications such as backplane technology in active-matrix displays and radio-frequency identification tags.      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

Comparative Study of the Low-Frequency-Noise Behaviors in a-IGZO Thin-Film Transistors With $hbox{Al}_{2}hbox{O}_{3}$ and $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ Gate Dielectrics

A comparative study is made of the low-frequency noise (LFN) in amorphous indium–gallium–zinc oxide (a-IGZO) thin-film transistors (TFTs) with $hbox{Al}_{2}hbox{O}_{3}$ and $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ gate dielectrics. The LFN is proportional to $hbox{1}/f^{gamma}$, with $gamma sim hbox{1}$ for both devices, but the normalized noise for the $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ device is two to three orders of magnitude lower than that for the $hbox{Al}_{2} hbox{O}_{3}$ device. The mobility fluctuation is the dominant LFN mechanism in both devices, but the noise from the source/drain contacts becomes comparable to the intrinsic channel noise as the gate overdrive voltage increases in $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ devices. The $hbox{SiN}_{x}$ interfacial layer is considered to be very effective in reducing LFN by suppressing the remote phonon scattering from the $hbox{Al}_{2}hbox{O}_{3}$ dielectric. Hooge's parameter is extracted to $sim !!hbox{6.0} times hbox{10}^{-3}$ in $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ devices.      

Lattice-Mismatched $hbox{In}_{0.4}hbox{Ga}_{0.6} hbox{As}$ Source/Drain Stressors With In Situ Doping for Strained $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ Channel n-MOSFETs

We report the first demonstration of a strained $hbox{In}_{0.53} hbox{Ga}_{0.47}hbox{As}$ channel n-MOSFET featuring in situ doped $hbox{In}_{0.4}hbox{Ga}_{0.6}hbox{As}$ source/drain (S/D) regions. The in situ silicondoped $hbox{In}_{0.4}hbox{Ga}_{0.6}hbox{As}$ S/D was formed by a recess etch and a selective epitaxy of $hbox{In}_{0.4}hbox{Ga}_{0.6}hbox{As}$ in the S/D by metal–organic chemical vapor deposition. A lattice mismatch of $sim$0.9% between $ hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ and $hbox{In}_{0.4} hbox{Ga}_{0.6}hbox{As}$ S/D gives rise to lateral tensile strain and vertical compressive strain in the $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ channel region. In addition, the in situ Si-doping process increases the carrier concentration in the S/D regions for series-resistance reduction. Significant drive-current improvement over the control n-MOSFET with Si-implanted $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ S/D regions was achieved. This is attributed to both the strain-induced band-structure modification in the channel that reduces the effective electron mass along the transport direction and the reduction in the S/D series resistance.      

Positive Bias Temperature Instability (PBTI) Characteristics of Contact-Etch-Stop-Layer-Induced Local-Tensile-Strained $hbox{HfO}_{2}$ nMOSFET

The positive bias temperature instability (PBTI) characteristics of contact-etch-stop-layer (CESL)-strained $hbox{HfO}_{2}$ nMOSFET are thoroughly investigated. For the first time, the effects of CESL on an $hbox{HfO}_{2}$ dielectric are investigated for PBTI characteristics. A roughly 50% reduction of $V_{rm TH}$ shift can be achieved for the 300-nm CESL $hbox{HfO}_{2}$ nMOSFET after 1000-s PBTI stressing without obvious $ hbox{HfO}_{2}/hbox{Si}$ interface degradation, as demonstrated by the negligible charge pumping current increase ($≪$ 4%). In addition, the $hbox{HfO}_{2}$ film of CESL devices has a deeper trapping level (0.83 eV), indicating that most of the shallow traps (0.75 eV) in as-deposited $ hbox{HfO}_{2}$ film can be eliminated for CESL devices.      

High-Density and Low-Leakage-Current MIM Capacitor Using Stacked $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Insulators

We have fabricated high-$kappa hbox{Ni}/hbox{TiO}_{2}/hbox{ZrO}_{2}/ hbox{TiN}$ metal–insulator–metal (MIM) capacitors. A low leakage current of $hbox{8} times hbox{10}^{-8} hbox{A/cm}^{2}$ at 125 $^{circ}hbox{C}$ was obtained with a high 38- $hbox{fF}/muhbox{m}^{2}$ capacitance density and better than the $hbox{ZrO}_{2}$ MIM capacitors. The excellent device performance is due to the lower electric field in 9.5-nm-thick $hbox{TiO}_{2}/ hbox{ZrO}_{2}$ devices to decrease the leakage current and to a higher $kappa$ value of 58 for $ hbox{TiO}_{2}$ as compared with that of $hbox{ZrO}_{2}$ to preserve the high capacitance density.      

The Electrical and Interfacial Properties of Metal-High-$kappa$ Oxide-Semiconductor Field-Effect Transistors With $hbox{LaAlO}_{3}$ Gate Dielectric

$hbox{LaAlO}_{3}$ is a promising candidate for gate dielectric of future VLSI devices. In this letter, n-channel metal–oxide–semiconductor field-effect transistors with $hbox{LaAlO}_{3}$ gate dielectric were fabricated, and the electron mobility degradation mechanisms were studied. The leakage current density is $hbox{7.6} times hbox{10}^{-5} hbox{A/cm}^{2}$ at $-!$ 1 V. The dielectric constant is 17.5. The surface-recombination velocity, the minority-carrier lifetime, and the effective capture cross section of surface states were extracted from gated-diode measurement. The rate of threshold voltage change with temperature $(Delta V_{T} / Delta T)$ from 11 K to 400 K is $-!$ 1.51 mV/K, and the electron mobility limited by surface roughness is proportional to $E_{rm eff}^{-0.66}$.      

Cubic-Structured $hbox{HfO}_{2}$ With Optimized Doping of Lanthanum for Higher Dielectric Constant

It is demonstrated that $hbox{HfO}_{2}$ films can have much higher dielectric-constant values than the usual reported value of 20–24 by optimized incorporation of lanthanum element and crystallization to cubic structure. When $hbox{HfO}_{2}$ with 8% La is crystallized into cubic structure, the film exhibits the $kappa$ value of $sim$ 38 which is the highest among ever reported $hbox{HfO}_{2}$ -based high-$kappa$ dielectrics. The increased $kappa$ value of $ hbox{HfO}_{2}$ with 8% La enables the leakage current to be reduced more than one order of magnitude lower, compared to amorphous-phase $hbox{HfO}_{2}$ under the same electric field. The dependence of film thickness and annealing temperature on the cubic crystallization is also reported.      

Improvement of Resistive Switching in $hbox{Cu}_{x} hbox{O}$ Using New RESET Mode

Wide dispersions of memory switching parameters are observed in resistive random access memory based on $hbox{Al/Cu}_{x}hbox{O/Cu}$ structure. Moreover, the switching instability induced by these dispersions is studied. In this letter, a ramped-pulse series operation method is put forward, which can improve switching stability and cycling endurance remarkably. A method for minimizing the dispersion of $V_{rm reset}$ by optimizing the amplitude of pulse is proposed further. The write–read–erase–read operations can be over $hbox{8} times hbox{10}^{3}$ cycles without degradation by using the new operation mode. The role of Joule heating behind this behavior of $ hbox{Al/Cu}_{x}hbox{O/Cu}$ device is discussed.      

Improvement of On–Off-Current Ratio in $ hbox{TiO}_{rm x}$ Active-Channel TFTs Using $hbox{N}_{2} hbox{O}$ Plasma Treatment

Without sacrificing the on-current in the transfer characteristics, we have successfully reduced the off-current part by the optimal $hbox{N}_{2}hbox{O}$ plasma treatment to improve the on–off-current ratio in n-type titanium oxide $( hbox{TiO}_{rm x})$ active-channel thin-film transistors. While the high-power (275 W) $hbox{N}_{2}hbox{O}$ plasma treatment oxidizes the whole $hbox{TiO}_{rm x}$ channel and results in the reduction of both on- and off-current, the optimized low-power (150 W) process makes the selective oxidation of the top portion in the channel and reduces only the off-current significantly. Increase in on–off ratio by almost five orders of magnitude is achieved without change in on-current by using the presented method.      

Nitrided Tetragonal $hbox{ZrO}_{2}$ as the Charge-Trapping Layer for Nonvolatile Memory Application

Employment of a tetragonal $hbox{ZrO}_{2}$ film as the charge-trapping layer for nonvolatile memory was investigated and the $ hbox{NH}_{3}$ nitridation effect of the $hbox{ZrO}_{2}$ film on memory performance was also explored in this letter. The permittivity of the tetragonal $hbox{ZrO}_{2}$ film is slightly reduced from 38.7 to 36.9 after nitridation; nevertheless, nitridation introduces more trapping sites and passivates the grain boundary channel which results in a high operation speed in terms of 2.6-V flatband voltage shift by programming at $+$10 V for 10 ms and a good retention characteristic with 20.2% charge loss after ten-year operation at 125 $^{circ}hbox{C}$, both are superior to that without $hbox{NH}_{3}$ nitridation. Most importantly, the process is fully compatible with existent ULSI technology and paves the way to adopt a high-permittivity crystalline dielectric as the charge-trapping layer for future high-performance nonvolatile memory.      

Low-Voltage Organic Field-Effect Transistor With PMMA/$ hbox{ZrO}_{2}$ Bilayer Dielectric

This paper reports on the application of a bilayer polymethylmethacrylate (PMMA)/ $hbox{ZrO}_{2}$ dielectric in copper phthalocyanine (CuPc) organic field-effect transistors (OFETs). By depositing a PMMA layer on $hbox{ZrO}_{2}$, the leakage of the dielectric is reduced by one order of magnitude compared to single-layer $hbox{ZrO}_{2}$. A high-quality interface is obtained between the organic semiconductor and the combined insulators. By integrating the advantages of polymer and high- $k$ dielectrics, the device achieves both high mobility and low threshold voltage. The typical field-effect mobility, threshold voltage, on/off current ratio, and subthreshold slope of OFETs with bilayer dielectric are $hbox{5.6}timeshbox{10}^{-2} hbox{cm}^{2}/hbox{V} cdot hbox{s}$, 0.8 V, $hbox{1.2} times hbox{10}^{3}$, and 2.1 V/dec, respectively. By using the bilayer dielectrics, the hysteresis observed in the devices with single-layer $hbox{ZrO}_{2}$ is no longer present.      

The $hbox{Pd/TiO}_{2}$/ $hbox{n}$-LTPS Thin-Film Schottky Diode on Glass Substrate for Hydrogen Sensing Applications

A $hbox{Pd/TiO}_{2}$/n-type low-temperature-polysilicon (n-LTPS) MOS thin-film Schottky diode fabricated on a glass substrate for hydrogen sensing is reported. The n-LTPS is an excimer-laser-annealed and $hbox{PH}_{3}$ -gas-plasma-treated amorphous-silicon (a-Si) thin film. At room temperature and $-$2-V bias, the developed MOS Schottky diode exhibited a high signal ratio of 1540 to 50 ppm of hydrogen gas, with a fast response time of 40 s, respectively. The signal ratio is better or comparable with that of other reported MOS-type hydrogen gas sensors prepared on Si or III–V compound substrate. In addition, the signal ratio is 7.6, 14, and 30 times over other interfering gases of $ hbox{C}_{2}hbox{H}_{5}hbox{OH}$, $hbox{C}_{2}hbox{H}_{4}$ , and $hbox{NH}_{3}$ at room temperature and a concentration of 8000 ppm at $-$2-V bias, respectively. Thus, the developed MOS Schottky diode shows promise for the future development and commercialization of a low-cost hydrogen sensor.      

Pentacene-Based Low-Voltage Strain Sensors With PVP/$ hbox{Ta}_{2}hbox{O}_{5}$ Hybrid Gate Dielectrics

Field-controllable pentacene-semiconductor-based strain sensors were fabricated with hybrid gate dielectrics using polyvinyl phenol (PVP) and high-$k$ inorganic tantalum pentoxide $(hbox{Ta}_{2}hbox{O}_{5})$ onto polyethylene naphthalate films. The $hbox{Ta}_{2}hbox{O}_{5}$ gate-dielectric layer combined with a thin PVP layer to form very smooth and hydrophobic surfaces turns out to improve the molecular structures of pentacene films significantly. The PVP– $hbox{Ta}_{2}hbox{O}_{5}$ hybrid-gate-dielectric films exhibit a high dielectric constant of 19.27 and a leakage-current density of as low as 100 $hbox{nA/cm}^{2}$ . The sensors employing a thin-film-transistor-like Wheatstone bridge configuration able to operate at reduced voltage ($sim$4 V) show good device characteristics with a field-effect mobility of 1.89 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$ and a threshold voltage of $-$0.5 V. The strain sensor characterized with bending at 45$^{circ}$ with respect to the bridge bias direction with different bending radii of 50-, 40-, 30-, 20-, and 8-mm displays output signals improved in linearity in a low range of operating voltages.      

Nonvolatile-Memory Characteristics of $hbox{AlO}^{-}$ -Implanted $hbox{Al}_{2}hbox{O}_{3}$

The nonvolatile-memory (NVM) characteristics of $hbox{AlO}^{-}$ -implanted $hbox{Al}_{2}hbox{O}_{3}$ structures are reported and shown to exhibit promising behaviors, including fast program/erase speeds and high-temperature data retention. Photoconductivity spectra show the existence of two dominant trap levels, located at around 2 and 4 eV below the conduction band minimum of $hbox{Al}_{2}hbox{O}_{3}$, and our calculations show that these levels are likely attributed to the defects in the $hbox{Al}_{2}hbox{O}_{3}$, such as the Al–O divacancy. The relative concentrations of these defects vary with the implant fluence and are shown to explain the NVM characteristics of the samples irradiated to different fluences.      

2 MHz AO $Q$ -switched ${rm TEM}_{00}$ Grazing Incidence Laser With 3 at.% Neodymium Doped Nd:YVO$_{4}$

We present a detailed experimental and theoretical study of the ultrahigh repetition rate AO $Q$ -switched ${rm TEM}_{00}$ grazing incidence laser. Up to 2.1 MHz $Q$-switching with ${rm TEM}_{00}$ output of 8.6 W and 2.2 MHz $Q$ -switching with multimode output of 10 W were achieved by using an acousto-optics $Q$ -switched grazing-incidence laser with optimum grazing-incidence angle and cavity configuration. The crystal was 3 at.% neodymium doped Nd:YVO$_{4}$ slab. The pulse duration at 2 MHz repetition rate was about 31 ns. The instabilities of pulse energy at 2 MHz repetition rate were less than ${pm}6.7hbox{%}$ with ${rm TEM}_{00}$ operation and ${pm}3.3hbox{%}$ with multimode operation respectively. The modeling of high repetition rate $Q$-switched operation is presented based on the rate equation, and with the solution of the modeling, higher pump power, smaller section area of laser mode, and larger stimulated emission cross section of the gain medium are beneficial to the $Q$-switched operation with ultrahigh repetition rate, which is in consistent with the experimental results.      

Extraction of the Effective Mobility of $ hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs

The extraction of the effective mobility on $hbox{In}_{0.53} hbox{Ga}_{0.47}hbox{As}$ metal–oxide–semiconductor field-effect transistors (MOSFETs) is studied and shown to be greater than 3600 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$. The removal of $C_{rm it}$ response in the split $C$–$V$ measurement of these devices is crucial to the accurate analysis of these devices. Low-temperature split $C$–$V$ can be used to freeze out the $D_{rm it}$ response to the ac signal but maintain its effect on the free carrier density through the substrate potential. Simulations that match this low-temperature data can then be “warmed up” to room temperature and an accurate measure of $Q_{rm inv}$ is achieved. These results confirm the fundamental performance advantages of $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs.