Poly(trimethylene terephthalate) nanocomposite fibers comprising different organoclays: Thermomechanical properties and morphology

Poly(trimethylene terephthalate) (PTT) nano composites were synthesized by in situ polymerization at high temperature with two thermally stable organoclays: 1,2‐dimethylhexadecylimidazolium‐montmorillonite (IMD‐MMT) and dodecyltriphenyl phosphonium‐MMT (C₁₂PPh‐MMT). PTT hybrid fibers with various organoclay contents were melt‐spun at various draw ratios (DRs) to produce monofilaments. The thermomechanical properties and morphologies of the PTT hybrid fibers were characterized using differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray diffraction, electron microscopy, and mechanical tensile properties analysis. The nanostructure of the hybrid fibers was observed by both scanning and transmission electron microscopy, which showed that the clay layers were well dispersed into the matrix polymer, although some clusters or agglomerated particles were also detected. Unlike the hybrids containing IMD‐MMT, the clay layers of the C₁₂PPh‐MMT hybrid fiber were more dispersed into the matrix polymer. The thermal stability and tensile properties of the hybrid fibers increased with increasing clay content for DR = 1. However, as DR increased from 1 to 9 the ultimate strength and initial modulus of the hybrid fibers with IMD‐MMT increased slightly whereas those of C₁₂PPh‐MMT hybrid fibers decreased slightly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4535–4545, 2006     

Preparation and characterization of nylon 6/organoclay nanocomposite filament fibers

A series of nylon 6 (NY6)/organoclay nanocomposites were prepared via in situ polymerization of ε‐caprolactam in the presence of 1,2‐aminododecanoic acid‐intercalated montmorillonite (ADA‐MMT) organoclay (1–5 wt%) using 6‐aminocaproic acid as polymerization catalyst. The extent of organoclay dispersion in NY6 matrix was analyzed using WAXD and SEM measurements. DSC studies revealed marginal shift in melting and melt‐crystallization peaks toward lower temperature with increasing clay content. Melt viscosity studies for NY6/ADA‐MMT exhibited higher shear‐thinning behavior than neat NY6 probably due to the slip between NY6 matrix and exfoliated organoclay platelets during shear flow. The prepared nanocomposites were melt‐spun and studied for their property improvements against varying clay content, draw ratios, and annealing conditions. Birefringence and sonic velocity values increased initially at lower draw ratios (≤2.5) due to increased orientation of molecular chains along the drawing direction but saturated at higher draw ratio (3.0) for all the samples. At the same draw ratio; compared to neat NY6, NY6/organoclay fibers showed increased chain orientation along the drawing direction which can be attributed to the “tethering effect” of organoclay on NY6 matrix. The initial modulus and stress at break were sensitive to factors such as draw ratio, clay content, and annealing conditions. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Synthesis and characterization of poly(butylene terephthalate) nanocomposite fibers: Thermo‐mechanical properties and morphology

Nanocomposites of poly(butylene terephthalate) (PBT) with the organoclay C₁₂PPh‐MMT were prepared using in situ intercalation polymerization. Hybrids with various organoclay contents were processed for fiber spinning to examine their thermal behavior, tensile mechanical properties, and morphologies for various draw ratios (DRs). The thermal properties (T_g, T_m, and T_Dⁱ) of the hybrid fibers were found to be better than those of pure PBT fibers and were unchanged by variation of the organoclay loading up to 2 wt %. However, these thermal properties remained unchanged for DRs ranging from 1 to 18. Most clay layers were dispersed homogeneously in the matrix polymer, although some clusters were also detected. The tensile properties of the hybrid fibers increased gradually with increasing C₁₂PPh‐MMT content at DR = 1. However, the ultimate strengths and initial moduli of the hybrid fibers decreased markedly with increasing DR. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1247–1254, 2006     

Crystallization behavior and morphology of double crystalline poly(trimethylene terephthalate)/poly(ethylene oxide terephthalate) copolymers

Double crystalline poly(trimethylene terephthalate)/poly(ethylene oxide terephthalate) copolymers (PTT/PEOT), with PTT content ranging from 16.5 to 65.5 wt%, were synthesized by melt copolycondensation. The morphological transformation of samples from microphase separation to macrophase separation was investigated by gel permeation chromatography and transmission electron microscopy. Differential scanning calorimetry and in situ wide‐angle X‐ray diffraction suggested that all copolycondensation samples displayed double crystalline behavior. The melt‐crystallization peak temperatures (T_{m, c} values) of PTT chains monotonously increased with increasing PTT content and were higher than that of homo‐PTT when the content of PTT was above 30.6 wt%. Interestingly, T_{m, c} values of PEOT chains were also increased with increasing PTT content. Polarized optical microscopy revealed that all copolycondensation samples studied could form ring‐banded spherulites and band spacing increased with increasing T_c values. In addition, band spacing decreased with increasing PTT content at a given T_c. Strangely, although PEOT was the main component in all copolycondensation samples, spherulitic morphology formed by the advance crystallization of PTT did not change after PEOT crystallization. Only a subtle change of quadrant tones was detected. © 2012 Society of Chemical Industry     

Thermal properties and non‐isothermal crystallization behavior of poly(trimethylene terephthalate)/poly(lactic acid) blends

Thermal properties and non‐isothermal melt‐crystallization behavior of poly(trimethylene terephthalate) (PTT)/poly(lactic acid) (PLA) blends were investigated using differential scanning calorimetry and thermogravimetric analysis. The blends exhibit single and composition‐dependent glass transition temperature, cold crystallization temperature (T_cc) and melt crystallization peak temperature (T_mc) over the entire composition range, implying miscibility between the PLA and PTT components. The T_cc values of PTT/PLA blends increase, while the T_mc values decrease with increasing PLA content, suggesting that the cold crystallization and melt crystallization of PTT are retarded by the addition of PLA. The modified Avrami model is satisfactory in describing the non‐isothermal melt crystallization of the blends, whereas the Ozawa method is not applicable to the blends. The estimated Avrami exponent of the PTT/PLA blends ranges from 3.25 to 4.11, implying that the non‐isothermal crystallization follows a spherulitic‐like crystal growth combined with a complicated growth form. The PTT/PLA blends generally exhibit inferior crystallization rate and superior activation energy compared to pure PTT at the same cooling rate. The greater the PLA content in the PTT/PLA blends, the lower the crystallization rate and the higher the activation energy. Moreover, the introduction of PTT into PLA leads to an increase in the thermal stability behavior of the resulting PTT/PLA blends. Copyright © 2011 Society of Chemical Industry     

Preparation and characterization of polyethylene–clay nanocomposites by using chlorosilane‐modified clay

Clay was modified by trimethylchlorosilane; after modification, hydroxyl groups at the edge of layers were reacted and CEC value was drastically decreased. Polyethylene–clay composites were prepared by melt compounding. Wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) showed that intercalated nanocomposites were formed using organoclay ion‐exchanged from chlorosilane‐modified clay, but conventional composites formed using organoclay directly ion‐exchanged from crude clay. Dynamic mechanical analysis (DMA) of PE and PE–clay composites was conducted; the results demonstrated that nanocomposites were more effective than conventional composites in reinforcement and addition of organoclay resulted in the increase of glass transition temperature (T_g), but crude clay had no effect on T_g of PE–clay composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 676–680, 2004     

Poly(trimethylene terephthalate) nanocomposite fibers by in situ intercalation polymerization: thermo-mechanical properties and morphology (I)

A series of poly(trimethylene terephthalate) (PTT) nanocomposites, containing an organically modified montmorillonite (C₁₂PPh-MMT), were prepared by in situ intercalation polymerization of dimethyl terephthalate (DMT) and 1,3-propanediol (PDO). The PTT nanocomposites were melt-spun at different organoclay contents and different draw ratios (DRs) to produce monofilaments. The nanocomposites were characterized by X-ray diffraction, electron microscopy, universal tensile testing, differential scanning calorimetry and thermogravimetric analysis. Some of the clay particles appeared well dispersed within the PTT matrix, while others were found to agglomerate with a size greater than 10 nm. The addition of a small amount of C₁₂PPh-MMT was sufficient to improve the thermo-mechanical properties of the PTT hybrid fibers. Both the thermal stability and the tensile strength increased with increasing clay content at DR=1. As the DR was increased from 1 to 9, the ultimate tensile strength of the hybrid fibers decreased, while the initial modulus remained constant.     

Preparation and characterization of polyurethane–organoclay nanocomposites

Nanocomposite polyurethane (PU)–organoclay materials have been synthesized via in‐situ polymerization. The organoclay is first prepared by intercalation of tyramine into montmorillonite (MMT)‐clay through ion exchange process. The syntheses of polyurethane–organoclay hybrid films containing different ratios of clay were carried out by swelling the organoclay into diol and diamine followed by addition of diisocyanate and then cured. The nanocomposites with dispersed and exfoliated structure of MMT were obtained as evidenced by X‐ray diffraction and scanning electron microscope. X‐ray diffraction showed that there is no peak corresponding to d₀₀₁ spacing in organoclay with the ratios up to 20 wt%. SEM images confirmed the dispersion of nanometer silicate layers in the polyurethane matrix. Also, it was found that the presence of organoclay leads to improvement in the mechanical properties. The tensile strength was increased with increasing the organoclay contents to 20 wt% by 221% in comparision to the PU with 0% organoclay. POLYM. COMPOS. 28:108–115, 2007. © 2007 Society of Plastics Engineers     

Poly(ethylene terephthalate) nanocomposite fibers by in situ polymerization: The thermomechanical properties and morphology

A series of nanocomposites of poly(ethylene terephthalate) (PET) with the organoclay dodecyltriphenylphosphonium‐mica (C₁₂PPh‐mica) were synthesized with the in situ polymerization method. PET hybrid fibers with various organoclay concentrations were melt‐spun at various draw ratios (DRs) to produce monofilaments. The thermomechanical properties and morphologies of the PET hybrid fibers were characterized with differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray diffraction, electron microscopy, and universal tensile analysis. The organoclay was intercalated in the polymer matrix at all magnification levels, and some of the agglomerated organoclay layers were greater than 50 nm thick. The thermal stabilities and initial tensile moduli of the hybrid fibers increased with an increasing clay content for DR = 1. For DR = 1, the ultimate tensile strengths of the PET hybrid fibers increased with the addition of clay up to a critical clay loading and then decreased above that critical concentration. However, the tensile mechanical properties of the hybrid fibers did not improve with increasing DR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2009–2016, 2005     

Effect of organoclay reinforcement on the curing characteristics and technological properties of SBR sulphur vulcanizates

Styrene‐butadiene rubber (SBR) nanocomposites with different organoclay contents (up to 15 phr) were prepared by a melt compounding procedure, followed by a compression‐molding step in which the SBR matrix was sulfur crosslinked. The vulcanizates were characterized in respect to their curing, mechanical and viscoelastic properties, and thermal stability. The optimum cure time decreased with increasing organoclay content. This effect was attributed to the ammonium modifier present in the organoclay, which takes part in the curing reaction acting like an accelerator. The results of mechanical test on the vulcanizates showed that the nanocomposites presented better mechanical properties than unfilled SBR vulcanizate, indicating the nanoreinforcement effect of clay on the mechanical properties of SBR/organoclay nanocomposites. The addition of organoclay did not significantly change the glass transition temperature. However, the heights of tan δ value at the glass transition temperature for the nanocomposites are lower than that of the unfilled SBR. This suggests a strong interaction between the organoclay and the SBR matrix as the molecular relaxation of the latter is hampered. The temperature at which 50% degradation occurs (T₅₀) and the temperature when the degradation rate is maximum (DTG_max) showed an improvement in thermal stability, probably related to the uniform dispersion of organoclay. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of clay and predispersion method on the structure and properties of polystyrene (PS)‐clay nanocomposites

To prepare the polystyrene (PS)‐clay nanocomposites via an in situ emulsion polymerization, a clay predispersion method, i.e. dispersing the organic clay in the emulsifier solution by the assistance of ultrasonic, was proposed in this study. The conventional method, predispersing the organic clay into the monomer, was also presented for the comparison. The morphology analysis based on the X‐ray Deflection (XRD) and Transmission Electronic Microscopy (TEM) results suggested that the more uniform clay dispersion in the final nanocomposites could be achieved through the new method. The inorganic clay (Na‐MMT) and two organic clays (C₁₈‐MMT and VC₁₈‐MMT) synthesized by exchanging inorganic cations with the trimethyloctadecyl ammonium chloride (OTAC) and the vinylbenzyldimethyloctadecyl ammoniun chloride (VOAC) were chosen to investigate the influence of the clay surface modification on the properties of nanocomposites. The Dynamic Mechanical Analysis (DMA) results showed the storage modulus G′s of the nanocomposites had different enhancements over that of the pure PS, especially when the temperature approached the glass transition temperature (T_g). The T_gs of the nanocomposites, however, varied with the microstructure and the interactions between the polymer and the clay layers. The Na‐MMT and VC₁₈‐MMT increased the T_g, while the T_gs of PS/C₁₈‐MMT nanocomposites were slightly lower than that of the pure PS. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Preparation and properties of montmorillonite‐based polyimide nanocomposites

Montmorillonite (MMT)‐based polyimide (PI) nanocomposites were prepared via two‐stage polymerization of PI using polyamic acid (PAA). The clay was organically modified using various alkylammonium ions to examine the effect of changes in alkyl length on the intercalation spacing of both the treated clays and their hybrids with PAA and PI. The intercalation behavior of clay in the PI matrix and its thermal and mechanical properties were investigated as a function of clay concentration. The d‐spacing of organically modified MMT (O‐MMT) increased with increasing length of the alkylammonium chain. PI/O‐MMT hybrids form exfoliated nanocomposites at clay concentrations below 2 wt%, while they form intercalated nanocomposites together with some exfoliated ones at clay contents exceeding 4 wt%. Young's modulus increased rapidly to a clay loading of 2 wt%, and leveled off with further increases in clay loading. The tensile strength at break increased rapidly up to a clay loading of 1 wt%, and then decreased sharply, while the strain at break showed a monotonic decrease with increasing clay loading from 0 to 8 wt%. The storage modulus, E′, in the temperature range below the glass transition temperature T_g, generally increased with increasing clay content, except at the highest clay content of 8 wt%. Copyright © 2004 Society of Chemical Industry     

Nanocomposites formed from linear low density polyethylene and organoclays

Polyethylene-clay nanocomposites were prepared by melt compounding various combinations of a maleic anhydride grafted linear low density polyethylene (LLDPE-g-MA), a linear low density polyethylene (LLDPE), and two organoclays. The two types of organoclay were selected to show the effect of the number of alkyl groups attached to the nitrogen of the organic modifier on exfoliation and improvement of mechanical properties. Nanocomposites derived from the organoclay having two alkyl tails, M₂(HT)₂, exhibited better dispersion and improvement of mechanical properties than nanocomposites based on the organoclay having one alkyl tail M₃(HT)₁. This result is the opposite of what is observed for nylon-6 nanocomposites. In addition, the rheological properties and gas permeability of the nanocomposites derived from the organoclay having two alkyl tails, M₂(HT)₂ were investigated. Both melt viscosity and melt tension (melt strength) increased with increased content of clay (MMT) and LLDPE-g-MA. Gas permeability was decreased by the addition of MMT.     

Effects of crystalline and orientational memory phenomena on the isothermal bulk crystallization and subsequent melting behavior of poly(trimethylene terephthalate)

The effects of crystalline and orientational memory phenomena on the subsequent isothermal crystallization and subsequent melting behavior of poly(trimethylene terephthalate) (PTT) were investigated by studying the effect of prior melt‐annealing temperature, T_f, on the subsequent isothermal crystallization kinetics, crystalline structure and subsequent melting behavior of neat and sheared PTT samples. On partial melting, choices of the T_f used to melt the samples played an important role in determining their bulk crystallization rates, in which the bulk crystallization rate parameters studied were all found to decrease monotonically with increasing T_f. The decrease in the values of these rate parameters with T_f continued up to a critical T_f value (ie ca 275 °C for neat PTT samples and ca 280 °C for PTT samples which were sheared at shear rates of 92.1 and 245.6 s^?1). Choices of the T_f used to melt neat PTT samples had no effect on the crystal structure formed. The subsequent melting behavior suggested that the T_f used to melt both neat and sheared samples had no effect on the peak positions of the melting endotherms observed and that the observed peak values of these endotherms for all sample types studied were almost identical. Copyright © 2004 Society of Chemical Industry     

Melting,crystallization behaviors,and nonisothermal crystallization kinetics of PET/PTT/PBT ternary blends

The melting, crystallization behaviors, and nonisothermal crystallization kinetics of the ternary blends composed of poly(ethylene terephthalate), poly(trimethylene terephthalate) (PTT) and poly(buthylene terephthalate) (PBT) were studied with differential scanning calorimeter (DSC). PBT content in all ternary blends was settled invariably to be one‐third, which improved the melt‐crystallization temperature of the ternary blends. All of the blend compositions in amorphous state were miscible as evidenced by a single, composition‐dependent glass transition temperature (T_g) observed in DSC curves. DSC melting thermograms of different blends showed different multiple melting and crystallization peaks because of their various polymer contents. During melt‐crystallization process, three components in blends crystallized simultaneously to form mixed crystals or separated crystals depending upon their content ratio. The Avrami equation modified by Jeziorny and the Ozawa theory were employed to describe the nonisothermal crystallization process of two selected ternary blends. The results spoke that the Avrami equation was successful in describing the nonisothermal crystallization process of the ternary blends. The values of the t_1/2 and the parameters Z_c showed that the crystallization rate of the ternary blends with more poly(ethylene terephthalate) content was faster than that with the lesser one at a given cooling rate. The crystal morphology of the five ternary blends investigated by polarized optical microscopy (POM) showed different size and distortional Maltese crosses or light spots when the PTT or poly(ethylene terephthalate) component varied, suggesting that the more the PTT content, the larger crystallites formed in ternary blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyester nanocomposite fibers: comparison of their properties with poly(ethylene terephthalate) and poly(trimethylene terephthalate) (II)

Summary Two polyester nanocomposites were synthesized, one with poly(ethylene terephthalate) (PET) and the other with poly(trimethylene terephthalate) (PTT), by using organoclay. The in-situ interlayer polymerization method was used to disperse the organoclay in polyesters at different organoclay contents and at different draw ratios to produce monofilaments. The thermal stability and tensile mechanical properties increased with increasing organoclay content at a DR=1 . However, the values of the tensile mechanical properties of the hybrid fibers decreased with increasing DR. The reinforcing effects of the organoclay of the PET hybrid fibers were higher than those of the PTT hybrid fibers.     

Polystyrene–organoclay nanocomposites prepared by melt intercalation,in situ,and masterbatch methods

In this study, polystyrene (PS)/montmorillonite nanocomposites were prepared by melt intercalation, in situ polymerization, and masterbatch methods. In the masterbatch method, as the first step, a high clay content composite of PS–organoclay (masterbatch) was prepared by in situ polymerization, and then the prepared masterbatch was diluted to desired compositions with commercial PS in a twin‐screw extruder. The structure and mechanical properties of the nanocomposites were examined. X‐ray diffraction (XRD) analysis showed that the d‐spacing of the in situ formed nanocomposites increased from 32.9 Å for the organoclay powder to 36.3 and 36.8 Å respectively in nanocomposites containing 0.73 and 1.6 wt% organoclay, indicating intercalation. However, the d‐spacing of the other prepared materials remained nearly unchanged when compared with pure organoclay powder. Thus, at these low clay contents, in situ formed nanocomposites showed the best improvement in mechanical properties including tensile, impact strength, and Young's modulus. In situ polymerization method did not prove to be efficient at high clay loadings in terms of intercalation and mechanical properties. At high clay loadings, the effects of the three methods in promoting mechanical properties were not significantly different from each other. POLYM. COMPOS., 27:249–255, 2006. © 2006 Society of Plastics Engineers     

Preparation and cure behavior of organoclay‐modified allyl‐functional benzoxazine resin and the properties of their nanocomposites

A new type of polybenzoxazine‐clay nanocomposites were prepared by the in‐situ polymerization of allyl‐functional benzoxazine monomer, bis(3‐allyl‐3,4‐dihydro‐2H‐1,3‐benzoxazinyl)isopropane (B‐ala), in the presence of two different types of organoclay, allyldimethylstearylammonium‐montmorillonite and propyldimethylstearylammonium‐montmorillonite. The organoclays were mixed with molten B‐ala, followed by pouring into glass mold and then gradual curing up to 250°C. DSC and IR were used to follow the cure behavior of B‐ala in the presence of organoclay, indicating that organoclays catalyzed the ring opening of cyclic benzoxazine structure. The XRD of the nanocomposites showed featureless patterns, suggesting the exfoliation of the organoclay into the matrix. The viscoelastic properties of the hybrids showed that the glass transition temperatures (T_g) of the nanocomposites shifted to lower temperature in the presence of small amount of organoclay, but T_g started to increase with the increase of the organoclay content. This result suggests that, in the presence of organoclay, the curing reaction of ally and benzoxazine occurred in a different way, resulting in a different network structure. However, the presence of dispersed layered silicates into the matrix enhanced the thermal stability over the neat thermoset resin. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Synthesis and properties of polyimide (containing naphthalene) nanocomposites with organo‐modified montmorillonites

2,7‐Bis(4‐aminophenoxy) naphthalene (BAPN), a naphthalene‐containing diamine, was synthesized and polymerized with a 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) to obtain a polyimide (PI) via thermal imidization. To enhance the thermal and mechanical properties of the polymer, PI–Montmorillonite (MMT) nanocomposites were prepared from a DMAc solution of poly(amic acid) and a DMAc dispersion of MMT, which were organo‐modified with various amounts of n‐dodecylamine (DOA) or cetylpyridium chloride (CPC). FTIR, XRD, and TEM (transmission electron microscopy) were used to verify the incorporation of the modifying agents into the clay structure and the intercalation of the organoclay into the PI matrix. Results demonstrated that the introduction of a small amount of MMT (up to 5%) led to the improvement in thermal stability and mechanical properties of PI. The decomposition temperature of 5% weight loss (T_d,5%) in N₂ was increased by 46 and 36°C in comparison with pristine PI for the organoclay content of 5% with DOA and CPC, respectively. The nanocomposites were simultaneously strengthened and toughened. The dielectric constant, CTE, and water absorption were decreased. However, at higher organoclay contents (5–10%), these properties were reduced because the organoclay was poorly dispersed and resulted in aggregate formation. The effects of different organo‐modifiers on the properties of PI–MMT nanocomposite were also studied; the results showed that DOA was comparable with CPC. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006