Experimental investigation of the performance and emissions of a heavy-duty diesel engine fueled with waste cooking oil biodiesel/ultra-low sulfur diesel blends

The major obstacle to biodiesel commercialization is the high cost of raw materials. Biodiesel from waste cooking oil is an economical source and thus an effective strategy for reducing the raw material cost. Using waste cooking oil also solves the problem of waste oil disposal. This study investigated the emissions of polycyclic aromatic hydrocarbons (PAHs), carcinogenic potencies and regulated matters, and brake specific fuel consumption from a heavy-duty diesel engine under the US-HDD transient cycle for five test fuels: ultra-low sulfur diesel (ULSD), WCOB5 (5 vol% biodiesel made from waste cooking oil + 95 vol% ULSD), WCOB10, WCOB20, and WCOB30. Experimental results indicate using ULSD/WCOB blends decreased PAHs by 7.53%-37.5%, particulate matter by 5.29%-8.32%, total hydrocarbons by 10.5%-36.0%, and carbon monoxide by 3.33%-13.1% as compared to using ULSD. The wide usage of WCOB blends as alternative fuels could protect the environment.     

Emission characteristics of a turbocharged diesel engine fueled with gas-to-liquids

Emission characteristics of a turbocharged, intercooled, heavy-duty diesel engine operating on neat gas-to-liquids (GTL) and blends of GTL with conventional diesel were investigated and a comparison was made with those of diesel fuel. The results show that nitrogen oxides (NO _x ), smoke, and particulate matter (PM) emissions can be decreased when operating on GTL and diesel-GTL blends. Engine emissions decrease with an increase of GTL fraction in the blends. Compared with diesel fuel, an engine operating on GTL can reduce NO _x , PM, carbon monoxide (CO), and hydrocarbon (HC) by 23.7%, 27.6%, 16.6% and 12.9% in ECE R49 13-mode procedure, respectively. Engine speed and load have great influences on emissions when operating on diesel-GTL blends and diesel fuel in the turbocharged diesel engine. The study indicates that GTL is a promising alternative fuel for diesel engines to reduce emissions. Translated from Transactions of CSICE, 2006, 24(6): 489–493 [译自: 内燃机学报]     

增压柴油机燃用天然气合成油排放特性的研究

对增压中冷柴油机燃用纯天然气合成油（Gas-to-Liquids，GTL）、柴油／GTL混合燃料的排放进行了外特性、负荷特性和欧洲ECE R49十三工况法的试验研究，并与柴油的排放进行了对比。研究表明：燃用GTL在所有工况下都能够有效降低NOx、烟度和PM，且掺混比例愈大，效果愈明显，CO和HC也有一定的改善；在ECE R49十三工况下纯GTL的NOx和PM排放分别降低了23．7％和27．6％，CO和HC分别降低了16．6％和12．9％；发动机工况对增压柴油机燃用所有燃料的排放有较大影响。结果表明GTL是柴油机有潜力的低排放代用燃料。     

Influence of pentanol and dimethyl ether blending with diesel on the combustion performance and emission characteristics in a compression ignition engine under low temperature combustion mode

Dimethyl ether (DME) and n-pentanol can be derived from non-food based biomass feedstock without unsettling food supplies and thus attract increasing attention as promising alternative fuels, yet some of their unique fuel properties different from diesel may significantly affect engine operation and thus limit their direct usage in diesel engines. In this study, the influence of n-pentanol, DME and diesel blends on the combustion performance and emission characteristics of a diesel engine under low-temperature combustion (LTC) mode was evaluated at various engine loads (0.2–0.8 MPa BMEP) and two Exhaust Gas Recirculation (EGR) levels (15% and 30%). Three test blends were prepared by adding different proportions of DME and n-pentanol in baseline diesel and termed as D85DM15, D65P35, and D60DM20P20 respectively. The results showed that particulate matter (PM) mass and size-resolved PM number concentration were lower for D85DM15 and D65P35 and the least for D60DM20P20 compared with neat diesel. D60DM20P20 turned out to generate the lowest NO_x emissions among the test blends at high engine load, and it further reduced by approximately 56% and 32% at low and medium loads respectively. It was found that the combination of medium EGR (15%) level and D60DM20P20 blend could generate the lowest NO_x and PM emissions among the tested oxygenated blends with a slight decrease in engine performance. THC and CO emissions were higher for oxygenated blends than baseline diesel and the addition of EGR further exacerbated these gaseous emissions. This study demonstrated a great potential of n-pentanol, DME and diesel (D60DM20P20) blend in compression ignition engines with optimum combustion and emission characteristics under low temperature combustion mode, yet long term durability and commercial viability have not been considered.     

Effect of manifold injection of hydrogen gas in producer gas and neem biodiesel fueled CRDI dual fuel engine

The high flammability of hydrogen gas gives it a steady flow without throttling in engines while operating. Such engines also include different induction/injection methods. Hydrogen fuels are encouraging fuel for applications of diesel engines in dual fuel mode operation. Engines operating with dual fuel can replace pilot injection of liquid fuel with gaseous fuels, significantly being eco-friendly. Lower particulate matter (PM) and nitrogen oxides (NO_x) emissions are the significant advantages of operating with dual fuel.Consequently, fuels used in the present work are renewable and can generate power for different applications. Hydrogen being gaseous fuel acts as an alternative and shows fascinating use along with diesel to operate the engines with lower emissions. Such engines can also be operated either by injection or induction on compression of gaseous fuels for combustion by initiating with the pilot amount of biodiesel. Present work highlights the experimental investigation conducted on dual fuel mode operation of diesel engine using Neem Oil Methyl Ester (NeOME) and producer gas with enriched hydrogen gas combination. Experiments were performed at four different manifold hydrogen gas injection timings of TDC, 5°aTDC, 10°aTDC and 15°aTDC and three injection durations of 30°CA, 60°CA, and 90°CA. Compared to baseline operation, improvement in engine performance was evaluated in combustion and its emission characteristics. Current experimental investigations revealed that the 10°aTDC hydrogen manifold injection with 60°CA injection duration showed better performance. The BTE of diesel + PG and NeOME + PG operation was found to be 28% and 23%, respectively, and the emissions level were reduced to 25.4%, 14.6%, 54.6%, and 26.8% for CO, HC, smoke, and NO_x, respectively.     

Assessment of energy performance and air pollutant emissions in a diesel engine generator fueled with water-containing ethanol–biodiesel–diesel blend of fuels

Biomass based oxygenated fuels have been identified as possible replacement of fossil fuel due to pollutant emission reduction and decrease in over-reliance on fossil fuel energy. In this study, 4 v% water-containing ethanol was mixed with (65–90%) diesel using (5–30%) biodiesel (BD) and 1 v% butanol as stabilizer and co-solvent respectively. The fuels were tested against those of biodiesel–diesel fuel blends to investigate the effect of addition of water-containing ethanol for their energy efficiencies and pollutant emissions in a diesel-fueled engine generator. Experimental results indicated that the fuel blend mix containing 4 v% of water-containing ethanol, 1 v% butanol and 5–30 v% of biodiesel yielded stable blends after 30 days standing. BD1041 blend of fuel, which composed of 10 v% biodiesel, 4 v% of water-containing ethanol and 1 v% butanol demonstrated −0.45 to 1.6% increase in brake-specific fuel consumption (BSFC, mL kW⁻¹ h⁻¹) as compared to conventional diesel. The better engine performance of BD1041 was as a result of complete combustion, and lower reaction temperature based on the water cooling effect, which reduced emissions to 2.8–6.0% for NO_x, 12.6–23.7% particulate matter (PM), 20.4–23.8% total polycyclic aromatic hydrocarbons (PAHs), and 30.8–42.9% total BaPeq between idle mode and 3.2 kW power output of the diesel engine generator. The study indicated that blending diesel with water-containing ethanol could achieve the goal of more green sustainability.     

Effect of natural antioxidant additive on hydrogen-enriched biodiesel operated compression ignition engine

The environmental degradation and depletion of fossil fuel, urges the need of renewable fuel for IC engines. Among the renewable fuel, biodiesel are widely used as alternative fuel but for recent years hydrogen is also considered as alternative fuel because of zero emission but it possess higher auto ignition temperature. In order to reduce the self-ignition temperature of hydrogen and another liquid fuel is mixed and operated as a dual fuel mode condition in CI engine. The current investigation aims to analyse the impact of natural antioxidant additive on hydrogen-enriched biodiesel operation in a diesel engine. During the experimentation process hydrogen is admitted at the intake manifold and B20 blend of juliflora biodiesel is injected in combustion cylinder. The three test fuel samples are used for the experimentation process such as diesel, B20 and B20 with hydrogen in different flow rates such as 8, 10, 12, 16,20lpm. B20 with hydrogen shows an increment of brake thermal efficiency (BTE). Among the test fuels B20 + 16lpm and B20 + 20lpm blends have better improvement of BTE of 28.815% and 28.32%, which is higher than the conventional engine at maximum load CO, HC emission is also lower for B20 + 16lpm and B20 + 20lpm than other blends but the NO_x emission increases of 26 and 28% than diesel respectively. In order to minimize the NO_x emission, natural antioxidant additive Melia Azedarach (MA) of 1000 ppm is added to B20 + 16lpm and found that B20 + 16lpm with MA shows an improvement of BTE 2.17% higher than B20 + 16lpm without additive and the NO_x emission for B20 + 16lpm with additive is 1079 ppm, which is 21.9% lower than B20 + 16lpm without additives. Therefore B20 + 16lpm with additive is superior than other test blends.     

代用燃料在柴油机中的应用研究

本文对植物油,生物柴油,乳化油,乙醇/柴油等的制备和理化特性进行了研究.通过柴油机台架试验,研究了柴油机燃用生物柴油、乙醇/柴油、微乳燃油的排放特性.对比试验表明:生物柴油CO,碳氢(HC)和颗粒物(PM)的比排放下降幅度分别为34.6％,40.2％和28.9％,但NOx比排放增加了6.63％;柴油机燃用乙醇/柴油时,...     

A critical review: Application of methanol as a fuel for internal combustion engines and effects of blending methanol with diesel/biodiesel/ethanol on performance,emission, and combustion characteristics of engines

This article presents a comprehensive overview of methanol as a potential oxygenated fuel for internal combustion engines. Here two approaches have been examined to evaluate the utilization of methanol, namely blending with diesel/biodiesel/methanol and premixing with intake air or fumigation. In conventional compression ignition engines, up to 95% and 25% diesel can be replaced by methanol through fumigation and blending, respectively. Higher latent heat of vaporization of alcohol led to lower peak in-cylinder pressure and NO_x; however, it negatively affects thermal efficiency and hydrocarbon and carbon monoxide emissions. Fumigation of alcohol requires modifications in the existing engine, whereas blending needed surfactants or additives to produce stable alcohol–diesel blends. High injection pressure and late direct injection, methanol–diesel blends have shown lower emissions and proved their potential as a suitable replacement for ethanol–diesel blends from the components durability perspective.     

The effect of biodiesel oxidation on engine performance and emissions

Biodiesel is an alternative fuel consisting of the alkyl monoesters of fatty acids from vegetable oils or animal fats. Previous research has shown that biodiesel-fueled engines produce less carbon monoxide, unburned hydrocarbons, and particulate emissions compared to diesel fuel. One drawback of biodiesel is that it is more prone to oxidation than petroleum-based diesel fuel. In its advanced stages, this oxidation can cause the fuel to become acidic and to form insoluble gums and sediments that can plug fuel filters. The objective of this study was to evaluate the impact of oxidized biodiesel on engine performance and emissions. A John Deere 4276T turbocharged DI diesel engine was fueled with oxidized and unoxidized biodiesel and the performance and emissions were compared with No. 2 diesel fuel. The neat biodiesels, 20% blends, and the base fuel (No. 2 diesel) were tested at two different loads (100 and 20%) and three injection timings (3° advanced, standard; 3° retarded). The tests were performed at steady-state conditions at a single engine speed of 1400 rpm. The engine performance of the neat biodiesels and their blends was similar to that of No. 2 diesel fuel with the same thermal efficiency, but higher fuel consumption. Compared with unoxidized biodiesel, oxidized neat biodiesel produced 15 and 16% lower exhaust carbon monoxide and hydrocarbons, respectively. No statistically significant difference was found between the oxides of nitrogen and smoke emissions from oxidized and unoxidized biodiesel.     

Fatty acid methyl esters (FAMEs) from castor oil: Production process assessment and synergistic effects in its properties

Fatty acid methyl esters (FAMEs) from castor oil have been synthesized by methanolysis catalyzed by sodium methoxide and the optimal transesterification conditions have been found. However, some properties of the castor FAME render it unsuitable in pure state for its direct use as fuel in internal combustion engines. Thus, blends with reference diesel have been prepared and their properties have been evaluated. Among these properties, the oxidative stability of the blends shows a negative anti-synergistic effect, that is, all the blends have an induction period lower than the pure reference diesel and the pure castor FAME. On the contrary, the lubricity shows a positive synergistic effect, the wear scar of the blends being always lower than those of the pure components. The cold-filter plugging point of the blends shows also a singular effect, since the filterability remains identical to that of the reference diesel until around 50 vol% of castor FAME has been blended with it. The blends of castor FAME and reference diesel until approximately 40 vol% of castor FAME meet most of the specifications of the EN 590 standard.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Experimental investigation of the combustion characteristics,emissions and performance of hydrogen port fuel injection in a diesel engine

Diesel engines are indispensable in daily life. However, the limited supply of petroleum fuels and the stringent regulations on such fuels are forcing researchers to study the use of hydrogen as a fuel. In this study, a diesel engine is operated using hydrogen–diesel dual fuel, where hydrogen is introduced into the intake manifold using an LPG-CNG injector and pilot diesel is injected using diesel injectors. The energy contents of the total fuel, 0%, 16%, 36% and 46% hydrogen (the 0% hydrogen energy fraction represents neat diesel fuel), were tested at 1300 rpm of constant engine speed and 5.1 kW of constant indicated power. According to test results, the indicated thermal efficiency of the engine decreases and the isfc increases with an increasing hydrogen energy fraction. Additionally, indicated specific CO, CO₂ and smoke emissions decrease with an increasing percentage of hydrogen fuel. However, indicated specific NO_x emissions do not change at the 16% hydrogen energy fraction, in other words, with an increase in the hydrogen amount (36% and 46% hydrogen energy fraction of total fuel), a dramatic increase (58.8% and 159.7%, respectively) is observed. Additionally, the peak in-cylinder pressure and the peak heat release rate values increase with the increasing hydrogen rate.     

Biofuels and thermal barrier: A review on compression ignition engine performance,combustion and exhaust gas emission

The performance of an internal combustion engine is affected when renewable biofuels are used instead of fossil fuels in an unmodified engine. Various engine modifications were experimented by the researchers to optimise the biofuels operated engine performance. Thermal barrier coating is one of the techniques used to improve the biofuels operated engine performance and combustion characteristics by reducing the heat loss from the combustion chamber. In this study, engine tests results on performance, combustion and exhaust emission characteristics of the biofuels operated thermal barrier coated engines were collated and reviewed. The results found in the literature were reviewed in three scenarios: (i) uncoated versus coated engine for fossil diesel fuel application, (ii) uncoated versus coated engine for biofuels (and blends) application, and (iii) fossil diesel use on uncoated engine versus biofuel (and blends) use on coated engine. Effects of injection timing, injection pressure and fuel properties on thermal barrier coatings were also discussed. The material type, thickness and properties of the coating materials used by the research community were presented. The effectiveness and durability of the coating layer depends on two key properties: low thermal conductivity and high thermal expansion coefficient. The current study showed that thermal barrier coatings could potentially offset the performance drop due to use of biofuels in the compression ignition engines. Improvements of up to 4.6% in torque, 7.8% in power output, 13.4% in brake specific fuel consumption, 15.4% in brake specific energy consumption and 10.7% in brake thermal efficiency were reported when biofuels or biofuel blends were used in the thermal barrier coated engines as compared to the uncoated engines. In coated engines, peak cylinder pressure and exhaust gas temperature were increased by up to 16.3 bar and 14% respectively as compared to uncoated condition. However, changes in the heat release rates were reported to be between ?27% and +13.8% as compared to uncoated standard engine. Reductions of CO, CO₂, HC and smoke emissions were reported by up to 3.8%, 11.1%, 90.9% and 63% respectively as compared to uncoated engines. Significant decreases in the PM emissions were also reported due to use of thermal barrier coatings in the combustion chamber. In contrast, at high speed and at high load operation, increase in the CO and CO₂ emissions were also reported in coated engines. Coated engines gave higher NO_x emissions by about 4–62.9% as compared to uncoated engines. Combined effects of thermal barrier coatings and optimisation of fuel properties and injection parameters produced further performance and emissions advantages compared to only thermal barrier coated engines. Overall, current review study showed that application of thermal barrier coatings in compression ignition engines could be beneficial when biofuels or biofuel blends are used instead of standard fossil diesel. However, more research is needed combining coatings, types of biofuels and other engine modifications to establish a concrete conclusion on the effectiveness of the thermal barrier when biofuels are used in the compression ignition engine. Reduction of NO_x emissions is another important R & D area.     

Exploration of engine characteristics in a CRDI diesel engine enriched with hydrogen in dual fuel mode using toroidal combustion chamber

The impact of dual fuel (diesel/hydrogen) on different performance aspects of CRDI diesel engines is investigated in this study. Amongst the fuel alternatives for IC (internal combustion) engines, the research described in this study recommended hydrogen as the least polluting and renewable in the long term. A CNG-LPG injector feeds hydrogen into the intake manifold, while diesel injectors pump pilot diesel to a DI engine adapted to hydrogen and diesel (dual-fuel mode). By maintaining 5.2 KW of consistent IP (Indicated Power) and engine speed at 1500 ± 10 rotations per minute (RPM), the hydrogen energy was varied in the dual fuel at 0% (100% diesel), 6%, 12%, 18% and 24%. With the increase in H₂ energy proportion, a decrease (5.2% decrease at 24% HES) in the BSEC (brake specific energy consumption) and the engine's BTE (brake thermal efficiency) is improved (7.85% increase at 24% HES). When emissions are considered, indicated NO_x increased (3.42%) while indicated CO₂ (3.61%), CO (2.84%), and smoke (4.85%) decreased with an increase in the proportion of hydrogen. Along with this, it was noted that the peak HRR (heat release rate) of 69.8 J/deg and in-cylinder pressure of 80.8 bar which increased significantly with the increase in hydrogen rate.     

Experimental investigations of performance and emissions of Karanja oil and its blends in a single cylinder agricultural diesel engine

An experimental investigation has been carried out to analyze the performance and emission characteristics of a compression ignition engine fuelled with Karanja oil and its blends (10%, 20%, 50% and 75%) vis-a-vis mineral diesel. The effect of temperature on the viscosity of Karanja oil has also been investigated. Fuel preheating in the experiments – for reducing viscosity of Karanja oil and blends has been done by a specially designed heat exchanger, which utilizes waste heat from exhaust gases. A series of engine tests, with and without preheating/pre-conditioning have been conducted using each of the above fuel blends for comparative performance evaluation. The performance parameters evaluated include thermal efficiency, brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and exhaust gas temperature whereas exhaust emissions include mass emissions of CO, HC, NO and smoke opacity. These parameters were evaluated in a single cylinder compression ignition engine typically used in agriculture sector of developing countries. The results of the experiment in each case were compared with baseline data of mineral diesel. Significant improvements have been observed in the performance parameters of the engine as well as exhaust emissions, when lower blends of Karanja oil were used with preheating and also without preheating. The gaseous emission of oxide of nitrogen from all blends with and with out preheating are lower than mineral diesel at all engine loads. Karanja oil blends with diesel (up to 50% v/v) without preheating as well as with preheating can replace diesel for operating the CI engines giving lower emissions and improved engine performance.     

Experimental investigations of performance,emission and combustion characteristics of Karanja oil blends fuelled DICI engine

Vegetables oils are simplest route of biofuel utilization in direct injection compression ignition (DICI) engines however several operational and durability problems are encountered while using straight vegetable oils in CI engines due to their high viscosity and low volatility. Reduction of viscosity by blending or exhaust gas heating leads to savings in chemical processing cost incurred on transesterification. In this experimental study, performance, emission and combustion characteristics of Karanja oil blends (K10, K20, K50 and K100) with mineral diesel were investigated in unheated conditions in a direct injection CI engine at different engine loads and constant engine speed (1500 rpm) vis-à-vis baseline data from mineral diesel. Analysis of performance parameters such as brake specific fuel consumption (BSFC), thermal efficiency, and exhaust gas temperature; mass emissions of various gaseous pollutant species; combustion parameters such as in-cylinder pressure rise, instantaneous heat release and cumulative heat release etc. were carried out. Detailed combustion analysis revealed that the combustion duration increased significantly even with smaller concentration of Karanja oil in the fuel blend. HC, CO and Smoke emissions were found to decrease for 20–50% (v/v) Karanja oil content in the fuel blends.     

Biodiesel fuel in diesel micro-turbine engines: Modelling and experimental evaluation

Many performance and emission tests have been carried out in reciprocating diesel engines that use biodiesel fuel over the past years and very few in gas turbine engines. This work aims at assessing the thermal performance and emissions at full and partial loads of a 30 kW diesel micro-turbine engine fed with diesel, biodiesel and their blends as fuel. A cycle simulation was performed using the Gate Cycle GE Enter software to evaluate the thermal performance of the 30 kW micro-turbine engine. Performance and emission tests were carried out on a 30 kW diesel micro-turbine engine installed in the NEST laboratories of the Federal University of Itajubá, and the performance results were compared with those of the simulation. There was a good agreement between the simulations and the experimental results from the full load down to about 50% of the load for diesel, biodiesel and their blends. The biodiesel and its blends used as fuel in micro-turbines led to no significant changes in the engine performance and behaviour compared to diesel fuel. The exhaust emissions were evaluated for pure biodiesel and its blends and conventional diesel. The results revealed that the use of biodiesel resulted in a slightly higher CO, lower NO_x and no SO₂ emissions.     

柴油机燃用大豆油甲酯的生命周期环境评价

近年来,生物柴油作为一种无毒的、可生物降解的、可再生的柴油机代用燃料倍受关注.但在选用其作为汽车代用燃料时,必须对其做出科学、客观的评估.为了能够正确评价生物柴油的能耗与排放,利用GREET1.7软件对柴油、大豆油甲酯和大豆油甲酯-柴油混合液的能耗和排放进行生命周期评价.研究结果表明,与柴油相比,随着掺混比的增大,能耗总量增大,化石燃料消耗减小,C02和GHGs排放降低,VOC、CO、NOxC02颗粒(PM 10和PM2.5)和SOx排放均升高.