Nb-Ti/Al/Ni/Au based ohmic contacts to AlGaN/GaN

In this paper, we report on a novel Nb-Ti/Al/Ni/Au metallic system proposed to form ohmic contact to AlGaN/GaN heterostructure. The metallic system uses deposition of thin niobium layer as the first layer in contact with the AlGaN barrier layer before deposition of the conventional Ti/Al/Ni/Au metallic system. The fabrication and electrical characterization of the Nb-Ti/Al/Ni/Au based ohmic contacts are presented. We have shown that Nb-based ohmic contacts at optimal alloying temperatures seem to be superior to that of conventional Ti/Al/Ni/Au in both surface morphology and contact resistivity evaluation. Auger Electron Spectroscopy (AES) and Secondary Ion Mass Spectroscopy (SIMS) are also used to evaluate the improved ohmic contact formation.     

Correlation between the performance and microstructure of Ti/Al/Ti/Au Ohmic contacts to p-type silicon nanowires

Understanding the electrical and microstructural aspects of contact formation at nanoscale is essential for the realization of low-resistance metallization suitable for the next generation of nanowire based devices. In this study, we present detailed electrical and microstructural characteristics of Ti/Al/Ti/Au metal contacts to p-type Si nanowires (SiNWs) annealed at various temperatures. Focused ion beam cross-sectioning techniques and scanning transmission electron microscopy (STEM) were used to determine the microstructure of the source/drain metal contacts of working SiNW field-effect transistors (FETs) annealed for 30 s in the 450-850?°C temperature range in inert atmosphere. Formation of titanium silicides is observed at the metal/semiconductor interface after the 750?°C anneal. Extensive Si out-diffusion from the nanowire after the 750?°C anneal led to Kirkendall void formation. Annealing at 850?°C led to almost complete out-diffusion of Si from the nanowire core. Devices with 550?°C annealed contacts had linear electrical characteristics; whereas the devices annealed at 750?°C had the best characteristics in terms of linearity, symmetric behavior, and yield. Devices annealed at 850?°C had poor yield, which can be directly attributed to the microstructure of the contact region observed in STEM.     

Structural and electrical properties of Au and Ti/Au contacts to n-type GaN

Au and Ti/Au layers were deposited on n-GaN. The samples were annealed at 400, 700 and 900 °C for 10 min in vacuum. The contacts were rectifying up to 700 °C and the highest Schottky barrier height of 1.07 eV was obtained for an Au single layer by current-voltage measurements. A binary phase of Au₂Ga was identified at the interface of the n-GaN/Ti/Au contact after annealing at 900 °C. The formation of Ti₂N and TiN (twin) phases epitaxially grown on GaN was also observed in the same contact as well as some gold diffusion into the topmost region of the GaN epilayer.     

Ti/Al/Ni/Au在N-polar GaN上的欧姆接触

N-polar GaN以其特有的材料特性和化学活性日益受到研究者关注,而N-polar GaN上欧姆接触也成为研究的热点。以Ti/Al/Ni/Au作为欧姆接触金属,分析了N-polar GaN上欧姆接触的最优退火条件,并借助剖面透射电子显微镜(TEM)和能量色散X射线能谱仪(EDX)研究了金属和N-polar GaN之间的反应生成物。结果表明,当退火温度升高到860℃时,可得到比接触电阻率ρc为1.7×10~(-5)Ω·cm~2的最优欧姆接触特性。TEM和EDX测试发现,除了生成已报道的AlN,还会在界面处产生多晶AlO_x,两者共同作用会进一步拉高势垒,从而对N-polar GaN上欧姆接触产生不利影响。     

Ni/Au、Pd/Au与p-AlGaN材料的接触特性

在AlGaNpin型日盲紫外探测器结构中的p-AlGaN层上生长了Ni/Au和Pd/Au,并在600～850℃温度下进行快速热退火,测量其退火前后传输线模型中各金属接触间的电学性质。实验发现,Ni/Au与Pd/Au在p-AlGaN上表现出了不同的接触性能。为了更好的说明金属与p-AlGaN材料接触之间在退火后电流的变化,还测量了p-AlGaN材料裸片两点之间I-V曲线在退火前后的变化。实验表明,比起Ni/Au来,Pd/Au在p-AlGaN材料上制备欧姆接触具有一定的优势,并在文中进行了分析。     

ZnO上欧姆接触的研究进展

为制备高性能的ZnO基器件如UV光发射器，探测器、场效应晶体管，在ZnO上形成优良的金属电极是十分必要的。回顾了近年来ZnO上制备欧姆接触的新进展，对在n型ZnO上制备欧姆接触的Al，A1/Pt，A1/Au，Ti/Al，Ti，AU，Ti/A1/Pt/Au，Re/Ti/Au等金属化方案的性能与特点，以及影响欧姆接触电阻率和热稳定性的因素，如表面处理和退火等进行了分析与归纳。同时，对P型ZnO上难以获得低接触电阻的原因进行了讨论。文章还简要说明了ZnO上透明欧姆接触的研究现状，指出获得低阻、高导电、高透光和高热稳定性的接触是未来ZnO基光电器件的发展方向。     

Metal contacts to n-type AlGaAs grown by molecular beam epitaxy

We report for the first time the barrier heights of Cu, Ni, Ag, Ti on etched n-type Al_0.33Ga_0.67As and their dependence on annealing temperature with I–V and C–V techniques. The barrier heights of Al and Au, measured for comparison, are 0.96 and 1.06 eV, respectively, in excellent agreement with the results reported previously. The barrier heights of the Cu, Ni, Ag and Ti/n---Al_0.33Ga_0.67As diodes are found to be 1.08, 0.90, 0.87 and 0.87 eV, respectively. It is observed that the barrier heights for Al, Au, Cu and Ti contacts monotonically decrease with annealing temperature. For the Ag and Ni contacts, however, they become higher after being annealed at 473 K for 10 min and become lower thereafter, accompanied by a change of their ideality factors in opposite direction. The barrier heights extrapolated from C–V measurements for all metals studied are higher than that deduced from I–V data, and become higher after annealing at high temperatures, indicating the existence of a thin oxide layer at interface and broadening of the oxide after annealing. Our results can be qualitatively explained by the quality of contact and defects created at the semiconductor surface due to interdiffusion.     

Influence of thermal treatment on the formation of ohmic contacts based on Ti/Al/Ni/Au metallization to n-type AlGaN/GaN heterostructures

Interfacial reactions between Ti/Al/Ni/Au metallization and GaN(cap)/AlGaN/GaN heterostructures at various annealing temperatures ranging from 715 to 865 °C were studied. Electrical current-voltage (I?CV) characteristics, van der Pauw Hall mobility measurements and surface topography measurement with atomic force microscopy (AFM) were performed. The ohmic metallizations were annealed at various temperatures in a rapid thermal annealing system and the annealing time of 60 seconds was kept for all samples. To study the influence of the parameters of annealing process on the properties of the 2 dimensional electron gas (2DEG) the van der Pauw Hall mobility measurement was used. Interfacial reactions between the contact metals and heterostructures were analyzed through depth profiles of secondary ion mass spectroscopy. It was observed that transition from nonlinear to linear I-V behavior occurred after the annealing at 805 °C. For the studied samples, the most promising results were obtained for the annealing temperature of 805 °C. This temperatue ensured not only low contact resistance but also made possible to preserve the 2DEG.     

Al and Ti/Al contacts on n-GaN

Al(60 nm) and Ti(40 nm)/Al(160 nm) metal layers have been deposited by thermal evaporation onto n-GaN epitaxial layers grown by metal organic chemical vapour deposition (MOCVD) on a c-plane sapphire substrate. The samples have been annealed at 300, 400, 700 or 900 °C for 10 min in vacuum. The microstructural and electrical properties of the contacts have been investigated by electron microscopy, X-ray diffraction and by current-voltage measurements. As-deposited Al and Ti/Al contacts were rectifying with Schottky barrier heights below 0.35 eV and 0.38 eV, respectively. After heat treatment at 300 °C and 400 °C both contacts exhibited linear current-voltage characteristics. After annealing at 700 °C Al contacts became rectifying with a barrier height of 0.42 eV, while Ti/Al contacts remained nearly linear at the same temperature. The electrical characteristics and XRD analysis indicated that the upper metal in Ti/Al contact diffused in the Ti layer already during deposition. Cross-sectional transmission electron microscopy revealed that in the case of Ti/Al contacts, the continuity of the Ti layers ceased when annealing above 700 °C. X-ray diffractions showed, that a Ti₂N interface phase formed in Ti/Al contacts at 700 and 900 °C, and an AlN interface phase developed in the same contact at 900 °C.     

AlGaN/GaN high electron mobility transistors with implanted ohmic contacts

Selective area silicon implantation for source/drain regions was integrated into the fabrication of molecular beam epitaxy-grown AlGaN/GaN HEMTs. Dopant activation was achieved by rapid thermal annealing at 1100 °C in flowing N₂ ambient for 120 s with an AlN encapsulation. Linear transmission line measurements showed that the resistance of the overlay Ti/Al/Ni/Au ohmic contacts was reduced by 61% compared to the control sample. After the Schottky Ni/Au gate formation, the typical DC characteristics displayed a higher current drive, smaller knee voltage and better gate control properties for HEMTs with implanted source and drain regions.     

Direct measurements of lateral variations of Schottky barrier height across "end-on" metal contacts to vertical Si nanowires by ballistic electron emission microscopy

Ballistic electron emission microscopy measurements on individual "end-on" Au Schottky contacts to vertical Si nanowires (NWs) indicate that the local Schottky barrier height at the contact edge is 23 ± 3 meV lower than at the contact center. Finite-element electrostatic simulations suggest that this is due to a larger interface electric field at the contact edge resulting from (equilibrium) positive charge in Si/SiO(2) interface states near the Au/NW contact, induced by local band bending due to the high work function Au film.     

Heat conduction across monolayer and few-layer graphenes

We report the thermal conductance G of Au/Ti/graphene/SiO(2) interfaces (graphene layers 1 ≤ n ≤ 10) typical of graphene transistor contacts. We find G ≈ 25 MW m(-2) K(-1) at room temperature, four times smaller than the thermal conductance of a Au/Ti/SiO(2) interface, even when n = 1. We attribute this reduction to the thermal resistance of Au/Ti/graphene and graphene/SiO(2) interfaces acting in series. The temperature dependence of G from 50 ≤ T ≤ 500 K also indicates that heat is predominantly carried by phonons through these interfaces. Our findings suggest that metal contacts can limit not only electrical transport but also thermal dissipation from submicrometer graphene devices.     

Investigation of interface properties of Ti/Ni/Ag thin films on Si substrate

The interface structure and the adhesion of direct current (DC) sputtered Ti/Ni/Ag thin film metallization on n⁺Si substrate has been investigated. It is shown that beside the chemical preparation of the Si surface prior to sputtering also thermal annealing of sputtered metal structure has strong influence on the adhesion of sputtered layers to the silicon. Energy dispersive X-ray spectroscopy (EDS) analysis were performed on both, the delaminated layers and on the silicon surface to determine the exact delaminating interface, which was found to be between Si and Ti layer. Auger electron spectroscopy (AES) profile revealed no traces of contamination at Ti-Si interface. Measured high tensile residual stress, particularly in sputtered Ni layer (1.4-2 GPa) is found to reduce the metal stack adhesion.     

Si基n型GaN的欧姆接触研究

GaN材料在光电子器件领域的广泛应用前景使得金属与其欧姆接触的研究成为必然。本文对Si基n型GaN上的Al单层及Ti/Al双层电极进行了研究。通过对不同退火条件下的I U特性曲线 ,X射线衍射以及二次离子质谱分析 ,揭示了界面固相反应对欧姆接触的影响 ,提出了改善这两种电极欧姆接触的二次退火方法     

Nano-scaled Pt/Ag/Ni/Au contacts on p-type GaN for low contact resistance and high reflectivity

We synthesized the vertical-structured LED (VLED) using nano-scaled Pt between p-type GaN and Ag-based reflector. The metallization scheme on p-type GaN for high reflectance and low was the nano-scaled Pt/Ag/Ni/Au. Nano-scaled Pt (5 A) on Ag/Ni/Au exhibited reasonably high reflectance of 86.2% at the wavelength of 460 nm due to high transmittance of light through nano-scaled Pt (5 A) onto Ag layer. Ohmic behavior of contact metal, Pt/Ag/Ni/Au, to p-type GaN was achieved using surface treatments of p-type GaN prior to the deposition of contact metals and the specific contact resistance was observed with decreasing Pt thickness of 5 A, resulting in 1.5 x 10(-4) ohms cm2. Forward voltages of Pt (5 A)/Ag/Ni contact to p-type GaN showed 4.19 V with the current injection of 350 mA. Output voltages with various thickness of Pt showed the highest value at the smallest thickness of Pt due to its high transmittance of light onto Ag, leading to high reflectance. Our results propose that nano-scaled Pt/Ag/Ni could act as a promising contact metal to p-type GaN for improving the performance of VLEDs.     

Microstructural analysis of Au/Pt/Ti contacts to p-type InGaAs

A detailed study on the microstructural changes that occur on annealing of Au/Pt/Ti ohmic contacts to n-type InGaAs has been carried out. The metal layers were deposited sequentially by electron beam evaporation onto InGaAs, doped with Zn to a level of 7 × 10¹⁸ cm^–3, that was epitaxially grown on < 100 > InP substrates. The deposition sequence and metal layer thicknesses were: Ti (25 or 30 nm), Pt (25 or 30 nm) and Au (250 or 300 nm). Samples were annealed at temperatures ranging from 250–425 C in a nitrogen atmosphere. As-deposited contacts were Schottky barriers, while a minimum contact resistance of 2 × 10^–5 cm² was obtained by annealing in the 375–425 C range. Annealing resulted in the inward diffusion of Ti and outward diffusion of In and As, leading to the formation of TiAs, metallic In and Ga-rich InGaAs at the Ti/InGaAs interface. The Pt diffusion barrier was effective in preventing In diffusion into the outer Au layer and minimizing Au diffusion to the semiconductor.     

金属/Hg1-xMnxTe接触的I-V特性研究

分别采用溅射和蒸发镀膜法在Hg1-xMnxTe试样表面形成了Au/Hg1-xMnxTe和Al/Hg1-xMnxTe接触,并用Aligent4155c I-V测试仪对其I-V特性进行了测量,随后对试样在10%NH4F:10%H2O2:H2O中进行了钝化处理,并对处理后的试样再次进行了I-V测量,对于测试结果用热电子发射-扩散理论进行了分析.结果表明:Au与Hg1-xMnxTe形成了良好的欧姆接触,而Al与Hg1-xMnxTe形成了具有整流特性的肖特基接触,其肖特基势垒的理论推算值为0.38eV.钝化处理后的试样,其表面漏电现象明显降低,Au/Hg1-xMnxTe接触的电流下降幅度在0.1V时最大,为76.1%;而Al/Hg1-xMnxTe接触在0.2V时最大,为93.2%.随着偏压的进一步增大,两种接触的电流减小的幅度都逐渐变小.     

Microstructural and electrical characteristics of rapidly annealed Ni/Mo Schottky rectifiers on cleaned n-type GaN (0001) surface

We have investigated the electrical and microstructural properties of Ni/Mo Schottky rectifiers to n-type GaN by current–voltage (I–V) and transmission electron microscopy (TEM) before and after annealing at 600 °C. The obtained barrier height for as-deposited Ni/Mo contact is 0.66 eV. It is observed that the barrier height increases with annealing temperature up to 500 °C, reaching a maximum value of 0.75 eV at this temperature. However, the Schottky barrier height of the Ni/Mo Schottky contact slightly decreased to 0.67 eV (I–V) when the contact was annealed at 600 °C. According to the HRTEM, STEM and EDX analysis, the formation of Ga-Ni interfacial layer at the interface results in the accumulation of gallium vacancies near the surface of the GaN layer. This could be the reason for increase in barrier heights upon annealing at elevated temperatures. The variation in the measured barrier height after annealing at 600 °C may be due to the formation of native oxide layer at the interface compared to the 500 °C annealed contact.     

Photoluminescence polarization in strained GaN/AlGaN core/shell nanowires

The optical polarization properties of GaN/AlGaN core/shell nanowire (NW) heterostructures have been investigated using polarization resolved micro-photoluminescence (μ-PL) and interpreted in terms of a strain-dependent 6 × 6 k·p theoretical model. The NW heterostructures were fabricated in two steps: the Si-doped n-type c-axis GaN NW cores were grown by molecular beam epitaxy (MBE) and then epitaxially overgrown using halide vapor phase epitaxy (HVPE) to form Mg-doped AlGaN shells. The emission of the uncoated strain-free GaN NW core is found to be polarized perpendicular to the c-axis, while the GaN core compressively strained by the AlGaN shell exhibits a polarization parallel to the NW c-axis. The luminescence of the AlGaN shell is weakly polarized perpendicular to the c-axis due to the tensile axial strain in the shell.     

Characterization of sputter deposited Au/Ni/Al multilayers on Si substrates

Multilayered Au/Ni/Al thin film metallization deposited by DC sputtering on n⁺Si substrates has been investigated. AES depth profiling was performed to reveal the concentration depth profiles of the Au/Ni/Al multilayers before and after annealing at different temperatures in the range 623-723 K. It was found that Ni aluminide layers begin to form during heat treatments at temperatures above 623 K. In addition to this process, Ni was found to diffuse significantly through the Au layer and segregates at the surface, proportionally to the increased annealing temperature. Consequently, the Ni oxidation process was found to take place thus causing the degradation of electrical contact. On the other hand Ni diffuses faster as well toward the Si/Al interface. No contamination traces at interfaces were observed. Electrical measurements of the metallized diode forward characteristics showed minor influence of the metallization heat treatment on the series resistance. Degradations were observed only in the reverse characteristics if the annealing was performed above 723 K.