Negative ion test facility ELISE—Status and first results

The new test facility ELISE (Extraction from a Large Ion Source Experiment) has been designed and installed since November 2009 at IPP Garching to support the development of the radio frequency driven negative ion source for the Neutral Beam System on ITER. The test facility is now completely assembled; all auxiliary systems have been commissioned and are operational. First plasma and beam operation is starting in October 2012.The source is designed to deliver an ion beam of 20 A of D^? ions, operating at 0.3 Pa source pressure at an electron to ion current ratio below 1. Beam extraction is limited to 60 kV for 10 s every 3 minutes, while plasma operation of the source can be performed continuously for 1 hour. The ion source and extraction system have the same width as the ITER source, but only half the height, i.e. 1 × 1 m² source area with an extraction area of 0.1 m². The aperture pattern of the extraction system and the multi driver source concept stay as close as possible to the ITER design. Easy access to the source for diagnostic tools or modifications allows to analyze and optimize the source performance. Among other possibilities many different magnetic filter field configurations inside the source can be realized to enhance the negative ion extraction and to reduce the co-extraction of electrons. Beam power and profiles are measured by calorimetry and thermography on an inertially cooled target as well as by beam emission spectroscopy. Cs evaporation into the source is done via two dispenser ovens.     

The ITER full size plasma source device design

In the framework of the strategy for the development and the procurement of the NB systems for ITER, it has been decided to build in Padova a test facility, including two experimental devices: a full size plasma source with low voltage extraction and a full size NB injector at full beam power (1 MV). These two different devices will separately address the main scientific and technological issues of the 17 MW NB injector for ITER. In particular the full size plasma source of negative ions will address the ITER performance requirements in terms of current density and uniformity, limitation of the electron/ion ratio and stationary operation at full current with high reliability and constant performances for the whole operating time up to 1 h. The required negative ion current density to be extracted from the plasma source ranges from 290 A/m² in D₂ (D^?) and 350 A/m² in H₂ (H^?) and these values should be obtained at the lowest admissible neutral pressure in the plasma source volume, nominally at 0.3 Pa. The electron to ion ratio should be limited to less than 1 and the admissible ion inhomogeneity extracted from the grids should be better than 10% on the whole plasma cross-section having a surface exposed to the extraction grid of the order of 1 m².The main design choices will be presented in the paper as well as an overview of the design of the main components and systems.     

The negative ion source test facility ELISE

The ITER neutral beam system is using inductively coupled radio frequency (RF) ion sources, that have demonstrated the required ITER parameters on (small) sources with extraction areas up to 200 cm². As a next step towards the full size ITER source IPP is presently constructing the test facility ELISE (“Extraction from a Large Ion Source Experiment”) operating with a “half-size” source which has approximately the width but only half the height of the ITER source. The modular driver concept is expected to allow a further extrapolation to the full size in one direction to be made. The main aim of this experiment is to demonstrate the production of a large uniform negative ion beam with ITER relevant parameters in stable conditions up to one hour.Plasma operation of the source is foreseen to be performed continuously for 1 h; extraction and acceleration of negative ions up to 60 kV is only possible in pulsed mode (10 s every 180 s) due to limitations of the existing IPP HV system. The design of the source and extraction system implements a high experimental flexibility and a good diagnostic access while still staying as close as possible to the ITER design. The main differences are the source operating in air and the use of a large gate valve between the source and the target chamber.ELISE is expected to start operation at the end of 2011 and is an important step for the development of the ITER NBI system; the experience gained early will support the design as well as the commissioning and operating phases of the PRIMA NBI test facilities and the ITER neutral beam system.     

Hydrogen incorporation in tungsten deposits growing by deuterium plasma sputtering

Tungsten deposits were produced by sputtering method using hydrogen isotope RF plasma, and the density and the incorporated components in the deposits were investigated. The density changed in the range from 14.2 g/cm³ to 6.1 g/cm³, and hydrogen isotope retention changed in the range from 0.25 to 0.05 as (H + D)/W by the difference of deposition conditions. Both the density and hydrogen isotope retention tended to decrease with an increase of pressure. Even though a deuterium gas was used for producing tungsten deposits, not only deuterium but also hydrogen, oxygen and water vapor were incorporated in the deposits. It is considered that the incorporation of these components originated in water vapor unintentionally existing in the vacuum chamber.     

EAST ion cyclotron resonance heating system for long pulse operation

Radio frequency (RF) power in the ion cyclotron range of frequencies (ICRF) is one of the primary auxiliary heating techniques for Experimental Advanced Superconducting Tokamak (EAST). The ICRF system for EAST has been developed to support long-pulse high-β advanced tokamak fusion physics experiments. The ICRF system is capable of delivering 12 MW 1000-s RF power to the plasma through two antennas. The phasing between current straps of the antennas can be adjusted to optimize the RF power spectrum. The main technical features of the ICRF system are described. Each of the 8 ICRF transmitters has been successfully tested to 1.5 MW for a wide range of frequency (25–70 MHz) on a dummy load. Part of the ICRF system was in operation during the EAST 2012 spring experimental campaign and a maximum power of 800 kW (at 27 MHz) lasting for 30 s has been coupled for long pulse H mode operation.     

Commissioning of the first KSTAR neutral beam injection system and beam experiments

The neutral beam injection (NBI) system was designed to provide plasma heating and current drive for high performance and long pulse operation of the Korean Superconducting Tokamak Advanced Research (KSTAR) device using two co-current beam injection systems. Each neutral beam injection system was designed to inject three beams using three ion sources and each ion source has been designed to deliver more than 2.0 MW of deuterium neutral beam power for the 100-keV beam energy. Consequently, the final goal of the KSTAR NBI system aims to inject more than 12 MW of deuterium beam power with the two NBI for the long pulse operation of the KSTAR. As an initial step toward the long pulse (～300 s) KSTAR NBI system development, the first neutral beam injection system equipped with one ion source was constructed for the KSTAR 2010 campaign and successfully commissioned. During the KSTAR 2010 campaign, a MW-deuterium neutral beam was successfully injected to the KSTAR plasma with maximum beam energy of 90 keV and the L-H transition was observed with neutral beam heating. In recent 2011 campaign, the beam power of 1.5 MW is injected with the beam energy of 95 keV. With the beam injection, the ion and electron temperatures increased significantly, and increase of the toroidal rotation speed of the plasma was observed as well. This paper describes the design, construction, commissioning results of the first NBI system leading the successful heating experiments carried in the KSTAR 2010 and 2011 campaign and the trial of 300-s long pulse beam extraction.     

Progress in development and design of the neutral beam injector for JT-60SA

Neutral beam (NB) injectors for JT-60 Super Advanced (JT-60SA) have been designed and developed. Twelve positive-ion-based and one negative-ion-based NB injectors are allocated to inject 30 MW D⁰ beams in total for 100 s. Each of the positive-ion-based NB injector is designed to inject 1.7 MW for 100 s at 85 keV. A part of the power supplies and magnetic shield utilized on JT-60U are upgraded and reused on JT-60SA. To realize the negative-ion-based NB injector for JT-60SA where the injection of 500 keV, 10 MW D⁰ beams for 100 s is required, R&Ds of the negative ion source have been carried out. High-energy negative ion beams of 490–500 keV have been successfully produced at a beam current of 1–2.8 A through 20% of the total ion extraction area, by improving voltage holding capability of the ion source. This is the first demonstration of a high-current negative ion acceleration of >1 A to 500 keV. The design of the power supplies and the beamline is also in progress. The procurement of the acceleration power supply starts in 2010.     

RADI—A RF source size-scaling experiment towards the ITER neutral beam negative ion source

IPP Garching is currently developing a negative hydrogen ion RF source for the ITER neutral beam system. The source demonstrated already current densities in excess of the ITER requirements (>200 A/m² D⁻) at the required source pressure and electron/ion ratio, but with only small extraction area and limited pulse length. A new test facility (RADI) went recently into operation for the demonstration of the required (plasma) homogeneity of a large RF source and the modular driver concept.The source with the dimension of 0.8 m × 0.76 m has roughly the width and half the height of the ITER source; its modular driver concept will allow an easy extrapolation in only one direction to the full size ITER source. The RF power supply consists of two 180 kW, 1 MHz RF generators capable of 30 s pulses. A dummy grid matches the conductance of the ITER source. Full size extraction is presently not possible due to the lack of an insulator, a large size extraction system and a beam dump.The main parameters determining the performance of this “half-size” source are the negative ion and electron density in front of the grid as well as the homogeneity of their profiles across the grid. Those will be measured by optical emission and cavity ring down spectroscopy, by Langmuir probes and laser detachment. These methods have been calibrated to the extracted current densities achieved at the smaller source test facilities at IPP for similar source parameters. However, in order to get some information about the possible ion and electron currents, local single aperture extraction with a Faraday cup system is planned.     

Permeation measurements for investigating atomic hydrogen flux and wall pumping/fuelling dynamics in QUEST

In order to investigate the overall atomic hydrogen background and the dynamic characteristics of wall pumping/fuelling phenomenon, a permeation probe system has been developed and applied in the spherical tokamak QUEST. Reliability of measurements, within ±3% accuracy and a positive correlation with the hydrogen line emission over three orders of magnitude have been demonstrated for more than 3000 various plasma discharges. By comparison of the experimental permeation (flux) curves with the numerically simulated curves, the net incident atomic hydrogen flux is evaluated in the range of 1 × 10¹⁹ H m^?2 s^?1 to 4 × 10²⁰ H m^?2 s^?1. The atomic flux has been investigated as a function of various plasma operation parameters like RF power, gas pressure and magnetic configuration. Using the static particle balance and permeation measurements, the progress in wall conditioning has been investigated. An inverse correlation between the atomic hydrogen flux and improvement in wall pumping has been observed over the two campaigns.     

Electrical and thermo-mechanical analysis of beam recovery system for megawatt power gyrotron

The paper presents the electrical and thermo-mechanical design of single stage beam recovery system for 120 GHz, 1 MW gyrotron. The electrical study shows that the cylindrical shape single stage beam recovery system enhances the efficiency by 66.26%. The maximum power deposited to collector in depressed collector operation is 0.48 MW for electronic efficiency, 30% and 1.44 MW for DC electron beam. The thermo-mechanical analysis has been performed to evaluate the water cooling system. The cooling system has capability of accommodating a peak wall loading, 0.9 kW/cm² at flow rate of 1500 l/min for safe operating time, 60 ms. Further, a high voltage analysis is also carried out to appraise the electric field distribution in the collector.     

Application of laser-induced breakdown spectroscopy for characterization of material deposits and tritium retention in fusion devices

Laser-induced breakdown spectroscopy (LIBS) is discussed as a possible method to characterize the composition, tritium retention and amount of material deposits on the first wall of fusion devices. The principle of the technique is the ablation of the co-deposited layer by a laser pulse with P (power density) ≥ 0.5 GW/cm² and the spectroscopic analysis of the light emitted by the laser induced plasma. The typical spatial extension of the laser plasma plume is in the order of 1 cm with typical plasma parameters of n_e ≈ 3 × 10²² m^?3 and T_e ≈ 1–2 eV averaged over the plasma lifetime which is below 1 μs. In this study “ITER-Like” mixed deposits with a thickness of about 2 μm and consisting of a mixture of W/Al/C and D on bulk tungsten substrates have been analyzed by LIBS to measure the composition and hydrogen isotopes content at different laser energies, ranging from about 2 J/cm² (0.3 GW/cm²) to about 17 J/cm² (2.4 GW/cm²) for 7 ns laser pulses. It is found that the laser energies above about 7 J/cm² (1 GW/cm²) are needed to achieve the full removal of the deposit layer and identify a clear interface between the deposit and the bulk tungsten substrate by applying 15–20 laser pulses while hydrogen isotopes decrease strongly after the first laser pulse. Under these conditions, the evolution of the spectral line intensities of W/Al/C/hydrogen can be used to evaluate the layer composition.     

Operational characteristics of the high flux plasma generator Magnum-PSI

In Magnum-PSI (MAgnetized plasma Generator and NUMerical modeling for Plasma Surface Interactions), the high density, low temperature plasma of a wall stabilized dc cascaded arc is confined to a magnetized plasma beam by a quasi-steady state axial magnetic field up to 1.3 T. It aims at conditions that enable fundamental studies of plasma–surface interactions in the regime relevant for fusion reactors such as ITER: 10²³–10²⁵ m⁻² s⁻¹ hydrogen plasma flux densities at 1–5 eV. To study the effects of transient heat loads on a plasma-facing surface, a high power pulsed magnetized arc discharge has been developed. Additionally, the target surface can be transiently heated with a pulsed laser system during plasma exposure. In this contribution, the current status, capabilities and performance of Magnum-PSI are presented.     

Aerosol formation and hydrogen co-deposition by colliding ablation plasma plumes of lithium and lead

In a high-repetition inertial fusion reactor, along with pellet implosions, the interior of target chamber is to be exposed to high-energy, short pulses of X-ray, unburned DT and He ash particles and pellet debris. As a result, wall materials will be subjected to ablation, ejecting particles in the plasma state to collide with each other in the center of volume. The interaction dynamics of ablation plasmas of lithium and lead, candidate first wall materials, has been investigated in the deposited energy density range from 3 to 10 J/cm²/pulse at a repetition rate of 10 Hz, each 6 ns long. The plasma density and electron temperature of colliding ablation plumes have been found to vary from the order of 10⁸–10¹³ 1/cm³ and from 0.7 to 1.5 eV, respectively. The formation of aerosol in the form of droplet has been observed with diameters between 100 nm and 10 μm. Also, hydrogen co-deposition has been found to occur particularly for colliding plumes of lithium, resulting in the H/Li atomic ratio from 0.15 to 0.27 in the hydrogen partial pressure range from 10 to 50 Pa.     

Hydrogen implantation defects in MgO

Deuterium and hydrogen ions with an energy of 15 keV have been implanted in virgin MgO (1 0 0) single crystals and in single crystals containing helium implantation generated microcavities. Doses were varied from 2 × 10¹⁵ to 2 × 10¹⁶ cm⁻². The samples were annealed from room temperature to 950 K. The defects produced by hydrogen and the trapping of hydrogen at the defects were monitored by photon absorption and positron beam analysis. With this novel technique a depth distribution of defects can be determined for implantation depths from 0 to 2000 nm. The technique is very sensitive for vacancy and vacancy clusters, i.e. sites with low electron density. After 950 K annealing microcavities were observed for the 2 × 10¹⁶ cm⁻² dose but not for the 10 times lower dose. During annealing up to 750 K point defects are mobile but the defect clusters remain small and filled with hydrogen. In samples which contain already microcavities, point defects and deuterium from the deuterium irradiation are accumulated by the microcavities.     

Progress of the RF negative hydrogen ion source for fusion at HUST

Huazhong University of Science and Technology has developed an experimental setup of a radio frequency (RF) driven negative hydrogen ion source, to investigate the physics of production and extraction of the H− ions for neutral beam injection in nuclear fusion reactors. The main design parameters of the ion source are: RF power ≤40 kW; extraction voltage ≤10 kV; accelerator voltage ≤20 kV. This paper gives an overview of the progress of the ion source with particular emphasis on some issues. The RF driver and source plasma are analyzed and optimized in terms of impedance matching, plasma characteristics and power coupling. In regard to the simulation analysis, a plasma model based on the particle-in-cell method and a beam trajectory model considering beam stripping loss are developed to investigate the plasma and negative ions transport inside the ion source. Furthermore, a collisional radiative model of H and H2 is built for plasma optical diagnosis.     

Study and optimization of boronization in Alcator C-Mod using the Surface Science Station (S3)

A Surface Science Station (S³) on the Alcator C-Mod tokamak is used to study and optimize the location and rate of boron film deposition in situ during electron cyclotron (EC) discharge plasmas using 2.45 GHz radio-frequency (RF) heating and a mixture of helium and diborane (B₂D₆) gasses. The radial profile of boron deposition is measured with a pair of quartz microbalances (QMB) on S³, the faces of which can be rotated 360° including orientations parallel and perpendicular to the toroidal magnetic field B_T ～0.1 T. The plasma electron density is measured with a Langmuir probe, also on S³ in the vicinity of the QMBs, and typical values are ～1 × 10¹⁶ m^?3. A maximum boron deposition rate of 0.82 μg/cm²/min is obtained, which corresponds to 3.5 nm/min if the film density is that of solid boron. These deposition rates are sufficient for boron film applications between tokamak discharges. However the deposition does not peak at the EC resonance as previously assumed. Rather, deposition peaks near the upper hybrid (UH) resonance, ～5 cm outboard of the EC resonance. This has implications for RF absorption, with the RF waves being no longer damped on the electrons at the EC resonance. The previously inferred radial locations of critical erosion zones in Alcator C-Mod also need to be re-evaluated. The boron deposition profile versus major radius follows the ion flux/density profile, implying that the boron deposition is primarily ionic. The application of a vertical magnetic field (B_V ～0.01 T) was found to narrow the plasma density and boron deposition profiles near the UH resonance, thus better localizing the deposition. A Monte Carlo simulation is developed to model the boron deposition on the different QMB/tokamak surfaces. The model requires a relatively high boron ion gyroradius of ～5 mm, indicating a B⁺¹ ion temperature of ～2 eV, to match the deposition on QMB surfaces with different orientation to B_T. Additionally, the boron ion trajectories become de-magnetized at high neutral gas throughput (～0.5 Pa m³ s^?1) and pressure (～2 Pa) when the largest absolute deposition rates are measured, resulting in deposition patterns, which are independent of surface orientation to B_T in optimized conditions.     

Nanosecond pulsed proton microbeam

We show the preparation of a pulsed 20 MeV proton beam at the Munich tandem accelerator which offers a fluence of more than 1 × 10⁹ protons/cm² being deposited in a beam spot smaller than 100 μm in diameter and within a time span of 0.9 ns fwhm. Such a beam is produced by an ECR type proton source using charge exchange in cesium vapor to obtain a beam of negative hydrogen of high brightness that is bunched, chopped, accelerated and then focused by the superconducting multipole lens of the microprobe SNAKE. Single beam pulses are generated in order to irradiate cell samples or tissue and to measure their biological effect in comparison to continuous proton or X-ray irradiation.     

Ion beam characterization of Fe-implanted GaN

Fe ion implantation in GaN has been investigated by means of ion beam analysis techniques. Implantations at an energy of 150 keV and fluences ranging from 2 × 10¹⁵ to 1 × 10¹⁶ cm^?2 were done, both at room temperature and at 623 K. Secondary Ions Mass Spectrometry was used to determine the Fe implantation profiles, whereas Rutherford Backscattering in channeling conditions with a 2.2 MeV ⁴He⁺ beam allowed us to follow the damage evolution. Particle Induced X-ray Emission in channeling conditions with a 2 MeV H⁺ beam was employed to study the lattice location of Fe atoms after implantation. The results show that a high fraction of Fe-implanted atoms are located in high symmetry sites in low fluence implanted samples, where the damage level is lower, whereas the fraction of randomly located Fe atoms increases by increasing the fluence and the resulting damage. Moreover, dynamical annealing present in high temperature implantation has been shown to favor the incorporation of Fe atoms in high symmetry sites.     

A bulk tungsten tile for JET: Heat flux tests in the MARION facility on the power-handling performance and validation of the thermal model

In the frame of the ITER-like Wall (ILW) for the JET tokamak, a divertor row made of bulk tungsten material has been developed for the position where the outer strike point is located in most of the foreseen plasma configurations. In the absence of active cooling, this represents a formidable challenge when one considers the temperature reached by tungsten (T_W,surf > 2000 °C) and the vertical gradient ?T/?z = 5 × 10⁴ K/m.As the development is drawing to an end and most components are in production, actual 1:1 prototypes are exposed to an ion beam with a power density around 7 MW/m² on the plasma-facing surface. Advantage is taken of the flexibility of the Marion facility to bombard the tungsten stack under shallow angles of incidence (～6°) with a powerful beam of ions and neutrals (>70 MW/m² on axis). The shallow angles are important, with respect to the toroidal wetted surface, for properly simulating the expected performance under actual tokamak conditions. The Marion tests have been used to validate for a few typical cases the thermal calculations that were steadily developed along with the tungsten tile and, at the same time, to gather information on the actual temperatures of individual components. The latter is an important factor to a finer estimation of the power handling capabilities.