Synthesis mechanism of LiNiVO4 by wet chemical method and mixed valence of nickel and vanadium

The single phase LiNiVO4 has been successfully synthesized by adopting a new mild liquid route with oxalic acid as both complexant and precipitant, and this method is named the CPG method. The products were obtained by sintering the dry gel precursor which was prepared by the CPG method at 200-850℃ for 2-10 h in air. The products were tested by XRD, XPS, ESR and TGA-DTA, and the resuits indicate that the single phase LiNiVO4 could be obtained at 450℃ for 2-3 h in air and LiNiVO4 was still steady at 850℃ for 10 h. The valence analyses show that in LiNiVO4 the valence of lithium is +1, both nickel and vanadium have the mixed valence, namely +2, +3 for nickel and +4, +5 for vanadium respectively. The LiNiVO4 can be expressed as LiNi3+xNi2+ 1-x V4+ x V5+ 1-x O4 (0≤x＜1). The pyrolysis mechanism of the dry gel is also discussed.     

The concentration quenching characteristics of 5D3-7FJ and 5D4-7FJ (J=0―6) transitions of Tb3+ in YBO3:Tb3+ phosphor

The photoluminescence quenching behaviors of ^5D3-^7Fj and ^5D4-^7Fj （J = 0—6） transitions of Tb^3＋ in YBO3：Tb under 130—290 nm excitation were systematically investigated. The results revealed that the quenching concentrations of both ^5D3-^7Fj and ^5D4-^7Fj transitions of Tb^3＋ in YBO3：Tb were mainly dependent on excitation wavelength. Particularly, the quenching concentrations of ^5D4-^7Fj transitions of Tb^3＋ under 130—290 nm excitation were correlated with excitation bands of YBO3：Tb. The quenching concentrations of ^5D3-^7Fj transitions remained at low concentration （2%） under 186—290 nm excitation and then increased gradually with energy of incoming excitation photon when excited at 130—186 nm. This dependence should be involved in their excitation mechanisms and quenching pathway in particular excitation region.[第一段]     

Preparation by a rheological phase reaction method and thermal decomposition reaction mechanism of nickelous salicylate tetrahydrate

0　IntroductionInrecentyears,studiesonBinghamfluid ,suchasElec trorheologicalfluid ,areactivelypursued[1 6] .Rheologicaltechniqueshavebeenplayinganimportantroleinsyntheticchem istry .Therheologicalphasereactionmethodisthe processofpreparingcompoundsormaterialsfromasolid liquidrheologicalmixture.Thatis,thesolidreactantsarefullymixedinapropermolarratio ,andmadeupbyaproperamountofwaterorothersolventstoaBinghambodyinwhichthesolidparticlesandliquidsubstanceareuniformlydistributed ,sothattheprodu…     

Effects of synthetic conditions on the structure and morphology of open-ended vanadium oxide nanotubes and study of their growth mechanism

Vanadium oxide nanotubes (VOx-NTs) have been synthesized by using n-butylamine as structuredirecting template and V2O5 as precursor under hydrothermal conditions. XRD, FTIR, SEM, TEM, BET and TG-DTA characterizations have been performed to both optimize the synthetic conditions and understand the growth mechanism of VOx-NTs. The results showed that open-ended VOx-NTs were obtained under the optimized conditions (hydrothermal temperature: 150―160°C, hydrothermal time: 5―7 d, the molar ratio of V2O5 to n-butylamine is 1:1) with diameters ranging from about 30 to 100 nm and several micrometers in length. The BET surface area and the desorption cumulative pore volume of pores of the as-synthesized sample were about 27.4609 m2/g and 0.191087 cm3/g, respectively. The result presents that the synthesis of VOx-NTs is controlled by the "rolling" mechanism and temperature is primary driving force for rolling.     

The formation and stability of Si1-x C x alloys in Si implanted with carbon ions

Si_1-xC_x alloys of carbon (C) concentration between 0.6%—1.0% were grown in Si by ion implantation and high temperature annealing. The formation of Si_1-xC_x alloys under different ion doses and their stability during annealing were studied. If the implanted dose was less than that for amorphizing Si crystals, the implanted C atoms would like to combine with defects produced during implantation and it was difficult to form Si_1-xC_x alloys after being annealed at 850℃. With the increment of implanted C ion doses, the lattice damage increased and it was easier to form Si_1-xC_x alloys. But the lattice strain would become saturate and only part of implanted carbon atoms would occupy the substitutional positions to form Si_1-xC_x alloys as the implanted carbon dose increased to a certain degree. Once Si_1-xC_x alloys were formed, they were stable at 950℃, but part of their strain would release as the annealing temperature increased to 1 000℃. Stability of the alloys became worse with the increment of carbon concentration in the alloys.     

Experimental and theoretical studies of the reaction between cationic vanadium oxide clusters and acetylene

The time of flight mass spectrometer coupled with a laser ablation/supersonic expansion cluster source and a fast flow reactor was adopted to study the reactivity of cationic vanadium oxide clusters （VinOS,） toward acetylene （C2H2） molecules under gas phase （P, - 1.14 kPa）, under near room temperature （T, - 350 K） conditions. Association products, VmOnC2H2^＋ （m,n = 2,4; 2,6; 3,7-8; 4,9-11; 5,12-13; 6,13-16, and 7,17）, are observed. The oxidation of C2H2 by （V2Os）n^＋ （n = 1 -3） is experimentally identified. The reactivity of （V2O5）n^＋ decreases as n increases. Density functional theory （DFT） calculations were carried out to interpret the reaction mechanisms. The DFT results indicate that a terminal oxygen atom from V2O5^＋ can transfer overall barrierlessly to C2H2 at room temperature, which is in agreement with the experimental observation. Other experimental results such as the observation of V206C2H2^＋ and nonobservation of V2O7,8C2H2^＋ in the experiments are also well interpreted based on the DFT calculations. The reactivity of vanadium oxide clusters toward acetylene and other hydrocarbons may be considered in identifying molecular level mechanisms for related heterogeneous catalysis.     

Dispersion of CoCl2 into γ-Al2O3 studied by positron

Co²⁺/γ-Al₂O₃ samples were prepared by incipient wetness impregnation of γ-Al₂O₃ with different concentration solution of CoCl₂ and dried at 40 °C. We measured the positron lifetime spectra of the samples of different Co²⁺ mass fractions (0%–8.24%) heated at different temperatures (100–500°C). All lifetime spectra were resolved into four components, in which the third and the fourth components were related to the surface state of the micropores and the secondary pores of the γ-Al₂O₃. The experimental results showed that the Co²⁺ was mainly located in the micropores and the secondary pores near to the exterior of the support. For low Co²⁺ mass fraction samples, when the heating temperature was above 400 °C, dispersal was almost finished. When the Co²⁺ mass fraction was above 5.59%, Co²⁺ and Cl⁻ were dispersed into the secondary pores in the form of multiple layers.     

NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> reduction by coupling combustion with recycling flue gas in iron ore sintering process

A new process called ‘NO _x reduction by coupling combustion with recycling flue gas (RCCRF)’ was proposed to decrease NO _x emission during the iron ore sintering process. The simulation test of NO _x reduction was performed over sintered ore and in the process of coke combustion. Experimentally, NO _x reduction was also carried out by sintering pot test. For sintered ore, the amount of NO _x emission is reduced by 15wt%–25wt% at 400–550°C using 2.0vol% H₂ or 2.0vol% CO, or reduced by 10wt%–30wt% at 560–720°C using 0.15vol% NH₃. NO _x reduction is around 10wt% by coupling combustion of pyrolysis gas and coke, or around 16wt% by recycling flue gas into coke combustion. By RCCRF, the maximum NO _x reduction ratio is about 23wt% in coke combustion experiment and over 40wt% in sintering pot test.     

Determination of crystal structure of omphacite

The chemical formula of omphacite was expressed with (MⅡ MⅠ ) (Si, AI)2O6. Cations that occupied the MⅡ site were large cations such as Ca or Na, and (Na/(Na+Ca)) ratio ranged from 0.2 to 0.8; the 6-coordinated MⅠ site accommodated cations such as Mg, Fe2+, Al, Fe3+ ,and(AI/(AI+Fe3+)) ratio was more than 0.5. Omphacite space groups reported were C2/ c, P2, P2/n, P2/c, cell parameters are α0 = 0.9600-0.9630 nm,b0 = 0.8750-0.8830 nm,c0 = 0.5230-0.5290 nm,β = 106°40′-107°10'. The sample was picked up from the eclogites in Zhucheng County, Shangdong Province. The intensity data were collected with the RIGAKU RASA Ⅱ -S four-circle single crystal diffractometer.The correct structure model was obtained by using the Patterson method and Fourier synthesis, SHELX-76 program, structure refinement with 905 independent diffraction points (| F0 |> 3σ |F0 |). After the structure parameter refinement, the R-factor reduced to 0.0515. The crystal structure analysis indicates that omphacite has a new space group-Pn space group.     

Degradation of 2, 4-D acid using Mn2+ as catalyst under UV irradiation

In this paper, the oxidative degradation of 2, 4-dichlorophenoxyacetic acid (2, 4-D) using Mn²⁺/H₂O₂ reagent under UV irradiation was studied. The results show that 2, 4-D was degraded more completely in Mn²⁺/H₂O₂ solution than traditional Fenton solutions. The effects of the concentration of Mn²⁺, H₂O₂ and pH were also investigated. And under the optimal condition of 1.48×10⁻⁴ mol/L, 8.99×10⁻⁵ mol/L and pH 3.38, the formation of ·OH was the most, both the decomposition rate of H₂O₂ and the degradation rate of 2, 4-D were the fastest. In addition, the photoreaction process was monitored using spin-trapping electron paramagnetic resonance (EPR), and the results indicated that the oxidative process was predominated mainly by the hydroxyl radical (·OH) gennerated in the system. Biography: HUANG Yingping (1964–), Professor, Ph. D., research direction: pollution ecology and water pollution control.     

Graded bandgap semiconductor thin film photoelectrodes

A graded bandgap oxide semiconductor thin film electrode was designed in order to obtain a photoelec-trochemically stable photoelectrode, with wide absorption range. The graded bandgap Ti_1−x V _x O₂ film electrode was prepared by heating the stacked layers of V/Ti in varying ratios, which were coated on the substrate by the sol-gel method using the starting solution with various V/Ti ratios. XPS result showed that the composition gradient was achieved for the film. The Ti_1−x V _x O₂ film electrode was found to be photoelectrochemically stable. Its photovoltage was about 360 mV. Obvious visible light photoresponse was observed for the Ti_1−x V _x O₂ film electrode. Compared with the pure TiO₂ electrode, the photocurrent onset potential of the Ti_1−x V _x O₂ film electrode was shifted positively, probably because the accumulation of vanadium at the electrode surface causes the recombination of the electrons and holes, and the lowest level of the conduction band of Ti_1−x V _x O₂ is lower than that of TiO₂. Impedance analysis showed that the donor density of the Ti_1−x V₂O₂ film electrode was higher than that of TiO₂ film electrode.     

SiO2 glasses synthesized at 355–445°C and 2.0–5.5 GPa

A series of SiO₂ glasses were synthesized by using spectroscopically pure silica on the YJ-3000 multi-anvil apparatus at 355–445°C and 2.0–5.5GPa. Their spectroscopic characteristics resemble that of the high-density quartz glass. In the meantime, the IR spectra of SiO₂ glasses show that a small amount of water exists in SiO₂ glasses in the form of OH^-. It may be due simply to the small amount of water that contributes significantly to the amorphism of SiO₂. The determination of refraction indices of SiO₂ glasses shows that the refraction indices of SiO₂ glasses and the high-density quartz glass are in good logarithmic relation with synthetic pressures.     

Effects of the mineral phase and valence of vanadium on vanadium extraction from stone coal

The influence of roasting on the leaching rate and valence of vanadium was evaluated during vanadium extraction from stone coal. Vanadium in stone coal is hard to be leached and the leaching rate is less than 10% when the raw ore is leached by 4 mol/L H₂SO₄ at 90℃ for 2 h. After the sample is roasted at 900℃ for 2 h, the leaching rate of vanadium reaches the maximum, and more than 70% of vanadium can be leached. The crystal of vanadium-bearing mica minerals decomposes and the content of V(V) increases with the rise of roasting temperature from 600 to 900℃, therefore the leaching rate of vanadium increases significantly with the decomposition of the mica minerals. Some new phases, anorthite for example, form when the roasting temperature reaches 1000℃. A part of vanadium may be enwrapped in the sintered materials and newly formed phases, which may impede the oxidation of low valent vanadium and make the leaching rate of vanadium drop dramatically. The leaching rate of vanadium is not only determined by the valence state of vanadium but also controlled by the decomposition of vanadium-bearing minerals and the existence state of vanadium to a large extent.     

柴油机SCR尿素喷射方式研究

鉴于柴油机选择性催化还原系统尿素喷射特性与氮氧（NO_x）转化效率密切相关,本文搭建SCR系统小样试验台,NO和NH₃作为主要试验用气,研究了不同氨氮比和不同温度条件下V₂O₅-WO₃/TiO₂催化剂的氨存储、氨泄漏以及NO_x转化效率的影响.结果表明:氨氮比越大,氨存储量的建立时间越短,NO_x转化效率的提升就越快;氨氮比为0.22时,15 s内NO_x转化效率从0增大到4.3%;当氨氮比为0.30时,15 s内NO_x转化效率从0增大到8.7%;随着氨氮比的增大氨泄漏会提前出现;氨氮比先大后小的喷射方法有利于改善NO_x转化效率.采用氨氮比先大后小的喷射方法,进行ETC标准循环测试,NO_x比排放从8.26 g/（kW·h）减少到1.91 g/（kW·h）,NH₃泄漏均值为5×10-6,峰值为18×10-6,满足国V排放法规要求.      

Fabrication and morphology of NbCx-C composite three-dimensinal netted fibers

The raw materials were commercial powders of Nb₂O₅ (99.95%), reactive carbon (99.99%), NaCI (99.95%) and sucrose (99.94%). By the carbothermal method, the NbC_x (x= 0.98)-C composite three-dimensional netted fibers were prepared in graphite resistance furnace in 0.1 MPa/N₂ ambient atmosphere at temperature from 970 to 1 120°C. The diameters of composite three-dimensional netted fibers are 12–38 μm, the hole circumferences of netted fibers are 0.22–2.2 mm and the hole diameters are 70–701 μm. The process conditions for fabricating NbC_x-C composite three-dimensional netted fibers and related morphology, composition and crystal structure of NbC_x-C composite netted fibers were investigated in detail.     

Magnetoelectric and converse magnetoelectric res ponses in TbxDy1-xFe2-y alloy ＆ Pb（Mg1/3Nb2/3）（1-x）TixO3 crystal laminated composites

Measured results of magnetoelectric （ME） and converse magnetoelectric （CME） effects of TbxDy1-xFe2-y/ Pb（Mg1/3Nb2/3）（1-x）TixO3/TbxDy1-xFe2-y （TD/PMNT/TD） and PMNT/TD/PMNT laminated composites are presented. ME effect was determined by measuring laminate voltage output under a Helmholtz-generated AC field biased by a DC field （0-1 kOe） （1Oe = 79.58 A/m）. The CME effect was measured by recording the voltage induced in a solenoid encompassing the ME sample while exposed to a DC bias field and PMNT layer driven by a 10 V AC source. The ME and CME responses in the two laminated structure are linear. The highest values of ME coefficients in TD/PMNT/TD and PMNT/TD/PMNT composites are 384 mV/Oe and 158 mV/Oe, respectively, while the highest values of CME coefficients in the two composites are 118 mG/V and 162 mG/V （1 G=10^-4 T）, respectively.     

铁镍磷化物电极材料的制备及电催化析氢性能

为了解决电解水析氢过程中所用贵金属材料的高昂成本问题,采用水热-低温磷化法制备了一种低廉、环保、高效的析氢催化剂Fe_xNi_1-x-P。与传统制备方法比较,该方法在水热合成前驱体过程中,利用镍盐和铁盐与无水乙醇发生氧化还原反应,生成的OH^-可以沉淀金属离子,随后前驱体与NaH₂PO₂低温磷化制得Fe_xNi_1-x-P。通过研究发现,Fe_0.5Ni_0.5-P电极材料表现出优异的催化活性。在1.0 mol·L^-1 KOH溶液中,电流密度为10 mA·cm^-2时,电极Fe_0.5Ni_0.5-P需要的过电位仅为113 mV,1 000圈循环伏安测试后,极化曲线无明显衰减。提供了一种制备Fe_xNi_1-x-P的简便方法,为开发清洁能源系统的环境友好型催化剂提供了新思路。     

Separation and analysis of the soluble trimer of Aβ1-40 and its effects on the rise in intracellular calcium

Alzheimer’s disease (AD) is one of the progressive neurodegenerative diseases associated with protein conformational transition, generally known as protein conformational disorders[1]. The general characteriza- tions of AD are the intracellular fibrillar…     

Synthesis of layered LiMnO2 byin situ oxidation-intercalation and a study of the reaction mechanism and electrochemical performance

Using Mn(OH)₂ as precursor, LiOH as lithiating agent and (NH₄)₂S₂O₈ as oxidant, layeredo-LiMnO₂ was obtained by a novel method—in situ oxidation-intercalation under mild conditions (80 °C). The product was characterized by XRD, ICP, TEM and⁷Li-NMR. The results reveal that orthorhombic LiMnO₂ with high purity and good crystallinity can be obtained by this method. During electrochemical tests, a LiMnO₂/Li cell shows an initial reversible capacity of 208 mAh · g⁻¹ and a reversible capacity of 180 mAh · g⁻¹ after 30 cycles at room temperature.     

Methane emissions from wetlands on the Qinghai-Tibet Plateau

The areal extent of cold freshwater wetlands on the Qinghai-Tibet Plateau (QTP) is estimated at 0.133 × 10⁶ km², suggesting a significant methane potential. Methane fluxes from wet alpine meadows, peatlands,Hippuris vulgaris mires and secondary marshes were 43.18, 12.96, −0.28 and 45.90 mg · m⁻² · d⁻¹, respectively based on the transect flux studies at the Huashixia Permafrost Station (HPS) from July to August 1996. Average CH₄ fluxes in the thaw season were extrapolated at 5.68 g · m⁻² according to the areal percentage of wetland areas in the Huashixia region. The CH₄ fluxes at four fixed sites, representative of similar ecosystems, ranged from −19.384–347.15 mg · m⁻² · d⁻¹, and the average CH₄ fluxes varied from 6.54 to 71.97 mg · m⁻² · d⁻¹ at each site during the observation period from April to September 1997. The CH₄ emissions at each site during the entire thaw season was estimated from 1.21 to 10.65 g · m⁻², displaying strong spatial variations. Seasonal variations of CH₄ fluxes also were observed at four sites: CH₄ outbursts occurred upon the spring thaw in May and June, CH₄ fluxes increased afterwards with rising soil temperatures. Episodic fluxes were observed in summer, which influenced the average CH₄ fluxes considerably. Annual CH₄ emissions from cold wetlands on the QTP were estimated at about 0.7–0.9 Tg based on the distribution of wetlands, representative CH₄ fluxes, and number of thaw days. The centers of CH₄ releasing were located in the sources of the Yangtze and Yellow rivers, and Zoigê Peatlands.