| ND钢连铸坯两相区内的微观偏析模型 |
| |
| 作者姓名： | 朱立光 刘震 韩毅华 |
| |
| 作者单位： | 1.华北理工大学冶金与能源学院, 唐山 063009 |
| |
| 基金项目： | 国家自然基金资助项目51604119国家自然基金资助项目51774141河北省自然科学基金-钢铁联合研究基金资助项目E5015209207 |
| |
| 摘 要： | 通过构建ND钢连铸坯凝固两相区内溶质的微观偏析模型, 不仅研究了C、S和P元素对固液两相区内钢的高温力学参数以及溶质再分配的影响, 还对P元素偏析比随冷却速率(CR) 的变化规律进行了探究.通过分析模型结果表明: 初始C的质量分数在0.075%~0.125%之间时, 随着初始C含量的增加, P、S元素的偏析加剧, 凝固末端温度下降幅度变大, 导致脆性温度区间增大; 增加P和S元素的初始含量, P、S元素的偏析比降低, 但会加剧其在枝晶间残余液相中的富集, 直接导致零塑性温度(ZDT) 下降; ND钢中的Cu含量低于显著提高裂纹敏感性的临界含量, 且凝固过程中Cu元素的偏析比较低, 因此在ND钢凝固过程中Cu元素不能主导裂纹的诱发; 在一定的冷却速率波动范围内, P元素的偏析比随着冷却速率(CR)的提高略有下降.
|
| 关 键 词： | 连铸坯 微观偏析 溶质再分配 偏析比 高温力学参数 |
| 收稿时间： | 2018-04-11 |
A microsegregation model in the two-phase region of an ND steel continuous casting billet |
| |
| Affiliation: | 1.College of Metallurgy and Energy, North China University of Science and Technology, Tangshan 063009, China2.Hebei Engineering Research Center of High Quality Steel Continuous Casting, Tangshan 063009, China |
| |
| Abstract: | ND steel is a low alloy steel that resists the dew point corrosion of sulfuric acid.To improve the special performance of ND steel, the chemical composition of ND steel not only contains conventional elements but also adds corrosion-resistant elements, such as Cu, Cr, and Ni.During the solidification process, the molten steel will undergo a phase change reaction.Owing to the differences in the distribution coefficients and diffusion coefficients of solute elements in different phases, solute elements will be redistributed in the solid-liquid two-phase region during solidification, which will lead to microsegregation of solute elements.The microsegregation of solute element makes the zero strength temperature and zero plasticity temperature (ZDT) of steel decrease, which makes the temperature range of brittleness expand and deteriorates the mechanical property of high temperature of the continuous casting billet, and finally increases the probability of inducing surface cracks.This paper takes the microsegregation of solute elements as the research background.Herein, a microsegregation model for the solute in the solidified two-phase region of an ND steel continuous casting billet was established.In the model, the effects of elements C, S, and P on high-temperature mechanical parameters and solute redistribution of steel in its solid-liquid two-phase region were studied, and the variation law of the segregation ratio of elemental P with cooling rate (CR) was also explored.According to the analysis of the model results, when the initial C content was between 0.075%and 0.125%, with an increase in the initial C content, segregation of P and S elements intensified, and the temperature drop at the solidification end became larger, leading to the increase in the brittle temperature range.According to the analysis of the model results, increasing the initial content of P and S will decrease the segregation ratio of P and S elements but will increase the enrichment content of P and S elements in the residual liquid phase between dendrites, directly leading to the decline of ZDT.Analysis of the model results shows that the Cu content in ND steel is lower than the critical content that significantly increases the crack sensitivity, and the segregation ratio of Cu element is at a low level during solidification.Therefore, elemental Cu cannot dominate the induced crack in ND steel during solidification.Finally, within a certain range of cooling rate fluctuation, the segregation ratio of P will decrease slightly with increasing CR. |
| |
| Keywords: | |
|
| 点击此处可从《》浏览原始摘要信息 |
|
点击此处可从《》下载全文 |
|
